Summary of Contents for DeDietrich Alezio V220 Evolution
Page 1
Export User Guide Reversible air / water heat pump "Split Inverter" ALEZIO V220 EVOLUTION AWHP-2 MIV-3 V220...
Page 2
Dear customer, Thank you for purchasing this appliance. Please read this manual carefully before using the product and keep it in a safe place for future reference. In order to ensure continued safe and efficient operation we recommend that the product is regularly maintained. Our Service and After Sales organization can assist with this.
1 Safety Safety General safety instructions Danger This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
1 Safety Note Remove the casing only to perform maintenance and repair work. Put the casing back in place after maintenance and repair work. Caution The appliance should be on Summer or Antifreeze mode rather than switched off to guarantee the following functions: Anti-blocking of pumps Frost Protection Note...
2 About this manual About this manual General This manual is intended for the end user of a AWHP-2 MIV-3 V220 heat pump. Symbols used 2.2.1 Symbols used in the manual This manual uses various danger levels to draw attention to special instructions.
4 Description of the product Description of the product General description The ALEZIO V220 EVOLUTION heat pump is composed of: A reversible outside module for energy production in Hot or Cold mode. An inside module with a control panel to handle the thermal exchange between the R410A fluid and the hydraulic circuit.
4 Description of the product Control panel description 4.3.1 Description of the keys Fig.2 Control panel SERVICE " " " 1 Escape key 3 Domestic hot water temperature key or 2 Heating temperature key or [Enter] key 4.3.2 Description of the display Fig.3 Key functions Back to the previous level without saving the modifications made...
Page 13
4 Description of the product Fig.5 Operating indicators A manual vent cycle is running Permanent display of the Information menu The screed drying function is active SERVICE Shut-down/Frost Protection mode Compressor on Electrical or hydraulic back-up running Cooling mode on Domestic hot water mode active "...
5 Operation Operation Using the control panel The various menus can be accessed using various key combinations. Fig.7 Accessing the menus 1. Simultaneously press the C ( ) and D keys. The symbol flashes. SERVICE " " " Fig.8 Scrolling through the menus 2.
5 Operation In the event of a prolonged absence (weekend, holiday), it is possible to switch to shutdown/frost protection mode. It is possible to produce domestic hot water all year round. User settings, page 17 Caution It is recommended that the heat pump never be completely shut down.
6 Settings Settings List of parameters 6.1.1 Choosing the hybrid operating mode Parameter Description Adjustment range Increment Factory setting Hybrid operating mode 0 to 2 0 = Deactivated 1 = Optimisation of primary energy consumption 2 = Optimisation according to energy cost (1) Only available if Note It is imperative that you input the energy cost parameters...
6 Settings User settings Note If no keys are pressed, the settings menus are exited automatically after 10 seconds without saving the parameters. 6.2.1 Modifying the room temperature set point Fig.9 Press the B key. 1. Press the B ( ) key.
6 Settings 6.2.3 Changing the operating mode 1. Press keys C ( ) and (D) simultaneously. The symbol flashes. 2. Confirm by pressing the D ( ) key. Fig.13 Modifying the value 3. Use the B ( ) or C key ( ) to modify the value.
6 Settings Fig.16 Selecting the forcing desired 2. Hold the A key down and press the D key successively to choose the forcing desired. SERVICE Display Back-up Forcing the back-up for heating Forcing the back-up for domestic hot water " "...
Page 20
6 Settings Parameter Description Unit Estimated electrical energy consumption in cooling mode (1)(2) (1) Display available if the estimated electrical energy consumption function is activated (2) Cooling mode must be enabled. The estimated electricity consumption is displayed in 3 digits. The first digit indicates the scale (x1, x10, x100, x1000).
Page 21
6 Settings Display example Description Fig.21 Unit 1000 kWh The displayed value is 123000 kWh. The unit is 1000 kWh. The first digit indicates the scale x 1000. Only the first 3 digits are displayed. SERVICE " " " 7612035 - v02 - 12062014 AWHP-2 MIV-3 V220...
7 Maintenance Maintenance General instructions Maintenance operations are important for the following reasons: To guarantee optimum performance. To extend the life of the equipment. To provide an installation which offers the customer optimum comfort over time. Caution An annual service of the heat pump is mandatory. Maintenance instructions 1.
7 Maintenance Note Filling and venting the installation twice a year should be sufficient to obtain an adequate hydraulic pressure. If it is often necessary to top up the installation with water, contact your installer. Venting the heating system It is essential that you vent any air in the domestic hot water tank, the pipes and the taps to prevent the annoying noises likely to be produced during heating or when drawing off water.
8 Troubleshooting Troubleshooting Error codes In the event of problems, the control panel displays the symbol and an error code. Caution Make a note of the code displayed. The error code is important for the correct and rapid diagnosis of the type of malfunction and for any technical assistance from your installer.
8 Troubleshooting Incidents and solutions Problems Probable causes Corrections The radiators are cold. The heating set point Increase the value of parameter or, if a room thermostat is temperature is too low. connected, increase the temperature on it. User settings, page 17. The heating mode is Activate the heating mode.
Page 26
8 Troubleshooting Problems Probable causes Corrections The water pressure is Not enough water in the Top up the installation with water. too low (< 1 bar). installation. Top up the installation with water, page 22. Water leak. Contact the installer. Clicking in the central The central heating pipe Contact the installer.
10 Environmental 10 Environmental 10.1 Energy savings Tips on saving energy: Do not block ventilation outlets. Do not cover the radiators. Do not hang curtains in front of the radiators. Install reflective panels behind the radiators to prevent heat losses. Insulate the pipes in rooms that are not heated (cellars and lofts).
11 Warranty 11 Warranty 11.1 General We would like to thank you for buying one of our appliances and for your trust in our product. In order to ensure continued safe and efficient operation we recommend that the product is regularly inspected and maintained. Your installer and our service department can assist with this.