Table of contents Chapter 1 Introduction Chapter 2 Quick start 2.1 Standard Shipment Package 2.2 Start up 2.3 Start up with Bluetooth 2.4 User’s Installation and Configuration Manual Chapter 3 Configuration 3.1 Programming Flow Chart 3.2 Factory Default Setting 3.3 General Process 3.4 Set All Default 3.5 Interface Chapter 4 RS232 parameters...
1. Introduction Thank you for purchasing this brand-new designed Linear Imager Handheld Bar code Scanner. VEGA is a cutting-edge gun-type linear imaging barcode scanner which is designed specifically for retail market. To the brand new series of VEGA, we add on more user friendly functions with detachable cable that makes it more easily to be operated by the customers.
Communication Cable (RS232,KBW or USB) c. Power Supply (if applicable) d. Quick Start Guide e. Stand for V-1010 or Bluetooth Cradle for V-1010BT g. Transparent Cover Plate Visually inspect the VEGA and accessories for any evidence of physical damage. If anything is missing or appears to be damaged, immediately contact your dealer.
2.4 User’s Installation and Configuration Manual In case you need more in depth information about the VEGA or more advanced setup options you can download the VEGA User’s Installation and Configuration Manual at web site: www.Scantech-ID.com / Support / Downloads...
3. Configuration 3.1 Programming Flow Chart Start Recall Set all Configuration Parameters* Default Interface Selection* Communication Parameters Bar codes Parameters Misc. Parameters* etc. Abort Configuration Configuration Save Parameters *Function not available in this guide. See User’s manual.
3.2 Factory Default Setting The VEGA is set with the factory default setting when you start-up the VEGA for the first time. The factory default settings are shown with <> and bold in the following sections. You can make your own settings by following the procedures in this guide.
3.3 General Process Step 1 Power on the scanner. Step 2 Scan Start of Configuration Step 3 Scan the programming codes for the desired features before scan end. Step 4 Scan End of Configuration Step 5 Save The settings will be saved permanently 3.4 Set All Default Set all the parameters to the factory default setting.
7. Symbologies 7.1 Enable All Symbologies Enable all bar codes 7.2 Enable / Disable Symbologies UPC-A<ON> UPC-A OFF UPC-E<ON> UPC-E OFF EAN-13/JAN-13<ON>...
Page 20
EAN-13/JAN-13 OFF EAN-8/JAN-8<ON> EAN-8/JAN-8 OFF CODE 39<ON> CODE 39 OFF Code 128<ON> Code 128 OFF Interleave 2 of 5<ON> Interleave 2 of 5 OFF...
Page 21
Codabar/NW7<ON> Codabar/NW7 OFF Industrial 2 of 5 ON Industrial 2 of 5<OFF> Matrix 2 of 5 ON Matrix 2 of 5<OFF> CODE 93 ON CODE 93<OFF> CODE 11 ON...
Page 22
CODE 11<OFF> MSI/PLESSEY ON MSI/PLESSEY <OFF> Telepen ON Telepen<OFF> China Postage ON China Postage<OFF> GS1 DataBar ON GS1 DataBar<OFF>...
Page 23
GS1 DataBar Expanded ON GS1 DataBar Expanded<OFF> GS1 DataBar Limited ON GS1 DataBar Limited<OFF> ATTENTION: The following symbologies are factory default enabled; UPC-A, UPC-E, EAN-8, EAN-13, Code 39, Code 128, Codabar, Interleaved 2 of 5.
8. Test Symbologies Scan one or more of these bar codes to test bar code symbologies you enabled. Codabar Code 39 Code 93 Code 128 EAN 8 EAN13 1234 5670 1 234567 890128 EAN 128 Interleaved 2 of 5...
V-1010 Indicator (led) Green = good read V-1010BT Indicator (led) Green = good read Red = low battery Blue = Bluetooth function 9.4 Electrical Characteristics (V-1010) Operation Voltage 5 VDC ±5% Current operating 140 mA (max)@ 5 VDC Current standby...
9.5 Electrical Characteristics (V-1010BT) Battery Li-ion 3.7V /1400 mA. Charge time 4.5 hours Reads per charge 30,000 Cradle indicator Green = good read (led) Blue = Bluetooth function Red / Green = Charging / Charge completed Operating Current 280 mA Input Voltage 5 VDC / 2A Input AC 100-240V...