Related Manuals for Eneo VKC-1395/12-24
Summary of Contents for Eneo VKC-1395/12-24
- Page 1 Full Manual 1/3" Camera, Day&Night, WDR, 2D-&3D-DNR, 750TVL, RS-485 VKC-1395 VKC-1395/12-24...
- Page 2 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
- Page 3 1. Read these instructions 2. Keep these instructions 3. Heed all warnings 4. Follow all instructions 5. Do not block any ventilat ion openings Install in accord ance with the manufacturer`s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat 7.
-
Page 4: Contents Of Package
CONTENTS OF PACKAGE INTRODUCTION CAMERA OVERVIEW MENU MAP CONTROL AND CONNECTIONS DAY&NIGHT I/O TERMINALS LENS SPECIFICATIONS Installation of the camera must be performed by qualified service personnel in accordance with all local and national electrical and mechanical codes. Carefully remove the color camera and its accessories from the carton and verify that they were not damaged in shipment. - Page 5 The camera provides a high-quality image using SONY Wide Dynamic 1/3” Super-HADII PS 960H CCD and digital signal processing LSI chips. 1/3" Super-HADII PS 960H CCD Super high-resolution of 750TV lines Wide Dynamic Range (~x512) -Double shutter+ATR-EX2 Auto Electronic Shutter [1/50(60) ~ 1/100,000] and manual electronic shutter modes [1/50(60) ~ 1/10,000] 0.1 lux(Colour), 0.01 lux(B/W), 0.001 lux(Slow-Shutter) @ F1.4 Sensitivity Digital Noise Reduction- 2D,3D...
- Page 6 (Option)
- Page 7 1/ 2 SCENE SELECT PICT ADJUST CUSTOM BRIGHTNESS EZOOM FULL AUTO CONTRAST INDOOR SHARPNESS TILT PRIVACY MASK OUTDOOR MOTION DET BACKLIGHT COLOR GAIN SYS SETTING EXIT RETURN RETURN 1/ 2 SHUTTER/AGC WHITE BAL HLC/BLC WDR/ATR-EX DAY/NIGHT IR OPTIMIZER RETURN AUTO AUTO MANUAL PUSH...
- Page 8 2/ 2 LENS SHD COMP DEFOG FLK LESS ANTI CR RETURN LEVEL AUTO AUTO PATTERN POSH POSV RETURN RETURN 1/ 2 SCENE SELECT PICT ADJUST EZOOM PRIVACY MASK MOTION DET SYS SETTING EXIT DETECT SENSE AREA SEL SYNC MODE INTERVAL DISPLY LENS BLOCK DISP...
- Page 9 2/ 2 LANGUAGE VERSION MAINTENANCE ENGLISH W.PIX MASK EXIT ESPANOL CAMERA RESET PYCCKNN PORTUGUES DEUTSCH FRANCAIS 日本語 RETURN RETURN AUTO DATA CLEAR MANUAL LEVEL1 REGISTRATION LEVEL2 REG.POINT AUTO CUSOR COLOR BLINK REG.NUMBER RETURN RETURN The six modes can be selected. CUSTOM /FULL AUTO / INDOOR / OUTDOOR / BACK LIGHT / ITS This mode turns off the auto scene recognition.
- Page 10 This Camera system provide functions that enable users to easily adjust the image quality to suit the image output device used. - Adjusts the brightness - Adjusts the image contrast (light and shade differences). - Adjusts the apparent resolution - Adjusts the hue - Adjusts the intensity (brilliance) of the colors - ON / OFF - Magnification rate = ZOOM (0~255)
- Page 11 External synchronization is a function with synchronization of the phase between an output video signal and an external reference signal. Use line lock mode to minimize color rolling. In this mode, synchronization is not implemented with a multiple number of cameras. In this mode, PLL is used to synchronize the vertical sync signal with the AC power supply with a power line frequency of 60 Hz (for the NTSC format) or 50 Hz (for the PAL format).
-
Page 12: Camera Id Setup
CAMERA ID SETUP. Sets the camera ID to ON or OFF. A title of 64 CAMERA ID Characters per line can be applied. Use the joystick to navigate the cursor. ABCDEFGHIJKLMNOPQRSTUVWXYZ 0123456789`~!@#$%^&*()-_=+<,>.?/;:’” Pushing centrally on the joystick will allow selection of that character. - Page 13 Manual white pixel defect information registration 1) Press the Enter button to turn White pixel compensation position marker display. 2) Use the Arrow buttons align the marker with the position of the white pixel. 3) Press the Enter button to exit and Press the EXIT button to save. Note : In manual detection mode, the detection data is always treated as a very large white pixel.
- Page 14 AEME (Auto Exposure / Manual Exposure) selection, shutter / AGC This type of control adjusts the exposure amount using the shutter speed. Exposure control is performed automatically. AE performs exposure control so that the OPD output level (evaluation value) is the target brightness level (AE reference level).
- Page 15 MWB allows WB control to be performed manually following the black body radiation curve. The configurable color temperature setting range is 1500K to 15000K. The setting can be performed in 64 steps. Holds the all pull-in frame The function first transfers to PUSH mode and performs pull-in operation, and then transfers to HOLD mode when pull-in is complete.
- Page 16 Camera automatically switches between Day&Night modes according to the D>N & N>D levels. : Select B/W Burst On/Off Selection of brightness reference for identifying Day/Night Control Signal. ILM levels external sensor inverting. external sensor non-inverting. Ext : Camera switches between Day & Night modes according to the D/N EXT input. (ILM level or GPI Cable) : Adjust the judgment time for the transition between the Day and Night.
- Page 17 The IR-SHD function compensates for observable events in which the light passing through the lens is imaged non-uniformly. Shading function ON/OFF selection Selects the shape of the ellipse (HIGH/MID/LOW) Use the center coordinate settings to adjust the shading compensation to the center position of the optical axis.
-
Page 18: Power Input Terminal
Terminal Block 1-1. DAY&NIGHT EXTERNAL INPUT (1pin) Switches the cameras D/N mode to either Day or Night based on the input status. Refer to the diagram below. The cameras D/N mode must be set to EXT for this to function. (GND) Open contact: DAY Close contact: NIGHT... -
Page 19: Installing Auto Iris Lens
LENS INSTALLING AUTO IRIS LENS... -
Page 20: Specifications
SPECIFICATIONS (Option) AC24V / DC12V- 210mA(2.5Watts) DC12V - 200mA(2.3Watts) 1/3" Super-HADII PS 960H CCD 1028(H)x508(V) 1028(H)x596(V) Effective pixels 976(H)x494(V) 976(H)x582(V) / Line Lock(Option) 750TVL 0.01 , 0.001Lux(Slow-shutter) Tact Switch, Coaxial COMM(32BIT),RS485(Pelco D) Lens DC / MANUAL Scene Select CUSTOM / FULL AUTO / INDOOR / OUTDOOR / BACKLIGHT / ITS White Balance ATW/ PUSH/ USER1/ USER2/ MANUAL/ PUSH LOCK 6~44.8DB... - Page 24 Videor E. Hartig GmbH Exclusive distribution through specialised trade chan- nels only. Videor E. Hartig GmbH Carl-Zeiss-Straße 8 · 63322 Rödermark/Germany Tel. +49 (0) 6074 / 888-0 · Fax +49 (0) 6074 / 888- Technical changes reserved www.videor.com...