Bosch GSB 13 Original Instructions Manual page 8

OBJ_BUCH-61-006.book Page 8 Tuesday, June 28, 2011 2:41 PM
8 | English
Impact Drill
Rotational speed under load, max.
Impact rate
Rated torque
Speed preselection
Right/left rotation
Spindle collar dia.
Max. drilling dia.
– Concrete
– Steel
– Wood
Chuck clamping range
Weight according to EPTA-Procedure
01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.
Assembly
Before any work on the machine itself, pull the mains
plug.
Auxiliary Handle (see figure A)
(GSB 13/GSB 13 RE/GSB 16/GSB 16 RE)
Operate your machine only with the auxiliary handle
11.
The auxiliary handle 11 can be set to any position for a secure
and low-fatigue working posture.
Turn the wing bolt for adjustment of the auxiliary handle 10 in
anticlockwise direction and set the auxiliary handle 11 to the
required position. Then tighten the wing bolt 10 again in
clockwise direction.
Adjusting the Drilling Depth (see figure A)
The required drilling depth X can be set with the depth stop
12.
Press the button for the depth stop adjustment 9 and insert
the depth stop into the auxiliary handle 11.
Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop correspond with the
desired drilling depth X.
Changing the Tool
Keyless Chuck (see figure B)
Hold the rear sleeve 3 of the keyless chuck 1 tight and turn the
front sleeve 2 in rotation direction
serted. Insert the tool.
Hold the rear sleeve 3 of the keyless chuck 1 tight and firmly
turn the front sleeve 2 in rotation direction
the locking action is no longer heard. This automatically locks
the drill chuck.
The locking is released again to remove the tool when the
front sleeve 2 is turned in the opposite direction.
1 609 929 M43 | (28.6.11)
GSB ... 10
Professional
-1
min 1610
-1
min 25700
Nm 1.5
–
–
mm 43
mm 10
mm 8
mm 20
mm 1.5 – 10 1.5 – 10
kg 1.5
/II
Key Type Drill Chuck (see figure C)
Wear protective gloves when changing the tool. The
drill chuck can become very hot during longer work peri-
ods.
Open the key type drill chuck 15 by turning until the tool can
be inserted. Insert the tool.
Insert the chuck key 14 into the corresponding holes of the
key type drill chuck 15 and clamp the tool uniformly.
Screwdriver Tools (see figure D)
When working with screwdriver bits 17, a universal bit holder
16 should always be used. Use only screwdriver bits that fit
the screw head.
For driving screws, always position the "Drilling/Impact Drill-
ing" selector switch 4 to the "Drilling" symbol.
Replacing the Drill Chuck
Removing the Drill Chuck (see figure E)
To dismount the keyless chuck 1, clamp an Allen key 18 into
the keyless chuck 1 and position an open-end spanner 19
(size 12 mm) against the spanner flats of the drive spindle.
Place the machine on a firm support, e.g., a workbench. Hold
the open-end spanner 19 firmly and loosen the keyless chuck
1 by turning the Allen key 18 in rotation direction
a tight seated keyless chuck by giving the long end of the Allen
key 18 a blow. Remove the Allen key from the keyless chuck
and completely unscrew the keyless chuck.
The key type drill chuck 15 is removed in the same manner as
, until the tool can be in-
the keyless chuck.
Mounting the Drill Chuck (see figure F)
The keyless chuck/key type drill chuck is mounted in reverse
by hand until
order.
10 RE 13 13 RE
1610 1570 1570
25700 25070 25070
1.5 1.8 1.8
– – –
–
43 43 43
10 13 13
8 10 10
20 25 25
1.5 – 13 1.5 – 13
1.5 1.7 1.7
/II /II /II
The drill chuck must be tightened with a tightening
torque of approx. 30–35 Nm.
16 16 RE
1640 1640
26270 26270
2.0 2.0
–
–
43 43
16 16
12 12
30 30
1.5 – 13 1.5 – 13
1.9 1.9
/II /II
. Loosen
Bosch Power Tools