Black & Decker KC4815 Manual page 5

c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk
of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding
of moving parts, breakage of parts and any other
condition that may affect the power tools operation. If
damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power
tools.
f. Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control. g. Use the power tool,
accessories and tool bits etc., in accordance with these
instructions, taking into account the working conditions
and the work to be performed. Use of the power tool for
operations different from those intended could result in a
hazardous situation.
5. Battery tool use and care
a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
b. Use power tools only with specifically designated battery
packs. Use of any other battery packs may create a risk
of injury and fire.
c. When battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails, screws,
or other small metal objects, that can make a connection
from one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
d. Under abusive conditions, liquid may be ejected from the
battery; avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause
irritation or burns.
6. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Special Safety Advice for Screwdriver
• Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring. Fasteners contacting a "live" wire may
make exposed metal parts of the powertool "live" and
could give the operator an electric shock.
• Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
• This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capa-bilities, or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
• The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those
recom-mended in this instruction manual may present a
risk of personal injury and/or damage to property.
Only plug the Battery Charger in 230V mains. Recharge the
Battery only with the provided charger. Before starting any
work on walls, floors or similar, make sure that all power lines
in the work area are switched off at the main switchboard.
Inspect the proposed drill hole location for any utility lines
(e.g. water, gas, power) before drilling. Use a suitable device
such as a metal or electricity line detecting device. If in doubt
contact a qualified electrician or your utility provider. Both
tools and work-pieces can heat up considerably during the
drilling operation. Allow a sufficient period of cooling before
handling. Wear appropriate gloves.
Warning! Impact wrenches are not torque
wrenches. Do not use this tool for tightening
fasteners to specified torques. An independent,
calibrated torque measurement device such as a torque
wrench should be used when under tightened or over
tightened fasteners can lead to the failure of the joint.
Safety Advice for Charger
Important! Danger! There are 4 pcs 1.2V Ni-cd battery in
screwdriver,Never short-circuit the battery or expose it to
moisture.Do not store it together with any metal parts which
could short-circuit the contacts.the machine could
overheat,start burning or explode.
ENGLISH
5