JVC KD-BT11 Instructions Manual page 230

INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Removing the unit
Before removing the unit, release the rear section.
When using the optional stay / 若選用支撐架
Fire wall
防火板
Dashboard
儀表板
Install the unit at an angle of less than 30˚.
將本機安裝在少於 30˚ 的角度。
* 1 When you stand the unit, be careful not to damage the fuse on the rear.
* 2 Not supplied for this unit.
TROUBLESHOOTING
• The fuse blows.
* Are the red and black leads connected correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the "–" terminals of L and R speakers grounded in common?
• Noise interfere with sounds.
* Is the rear ground terminal connected to the car's chassis using shorter and thicker cords?
• This unit becomes hot.
* Is the speaker output lead grounded?
* Are the "–" terminals of L and R speakers grounded in common?
• This unit does not work at all.
* Have you reset your unit?
When installing the unit without using the sleeve / 若不使用外套機殼安裝本機
In a Toyota car for example, first remove the car radio and install the unit in its place.
Stay (option) 以豐田牌（TOYOTA）汽車為例：首先取出汽車收音機，然後將本機裝入其空出的位置。
支撐架（選用的）
Screw (option)
螺絲釘（選用的）
Note
注意
安裝（裝設、固定在儀表板內）
下面的圖解表示了典型的安裝程序。如果您有問題，或需要有關配套元件的資料，請向 JVC 汽
車音響分銷商或配套元件供應公司詢問。
• 如果您不能確定如何正確地安裝本機，應請合格的技術人員來安裝。
Do the required electrical connections.
進行所需的電路連接。
拆卸本機
在拆卸本機前，應將本機後部的固定和連接部分鬆開。
Insert the two handles, then pull them
as illustrated so that the unit can be
removed.
按圖所示，將兩片板條型把手插入卡
槽，然後輕穩地從兩側向外拉兩片把
手，本機隨之拉出。
Flat head screws (M5 × 8 mm)
平頭螺絲釘（M5 × 8 mm）
2
Bracket *
托座 * 2
Pocket
空殼
: When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws are
used, they could damage the unit.
： 把本機安裝在托座上時，務必使用 8 mm 長的螺絲釘。如使用過長的螺絲釘，會損壞本機。
*
1 您豎起本機時，小心不要損壞底部的保險絲。
*
2 不隨本機提供。
故障排除
• 保險絲燒斷。
* 檢查紅色導線接頭和黑色導線接頭是否接觸正確?
• 電源不能接通。
* 檢查黃色導線接頭是否接上?
• 揚聲器沒有聲音。
* 檢查揚聲器輸出導線接頭是否短路?
• 聲音失真。
* 檢查揚聲器輸出端子是否接地?
* 檢查揚聲器的左（L）、右（R）端子的負極"–"是否共同接地?
• 噪音干擾音響。
* 後接地端子與車身是否使用較短和較厚的電線連接?
• 本機發熱。
* 檢查揚聲器輸出端子是否接地?
* 檢查揚聲器的左（L）、右（R）端子的負極"–"是否共同接地?
• 本機完全不能操作。
* 您是否已經重置您的機組?
2
Bend the appropriate tabs to hold the
sleeve firmly in place.
弄彎機殼的突舌，把外套機殼牢固
在儀表板內。
2
*
2
*
Flat head screws (M5 × 8 mm)
平頭螺絲釘（M5 × 8 mm）
Bracket * 2
2
托座 *
2
*
* 2