Related Manuals for WAFER GSM-KEY-ADC200
Summary of Contents for WAFER GSM-KEY-ADC200
- Page 1 WAFER GSM-KEY REMOTE CONTROL UNIT GSM-KEY-ADC200 MANUAL ADC200 VERSION 5.0 SHANGHAI WAFER MICROELECTRONICS CO.,LTD http://www.waferstar.com...
-
Page 2: Product Description
GSM-KEY-ADC OPERATING INSTRUCTIONS PRODUCT DESCRIPTION WAFER GSM-KEY is an electronic board with an on-board GSM modem.The purpose of this device is to open an electric gate by means of a GSM phone.It has a door open relay whose contact has to be connected in parallel with the button which opens the gate. It has a White List of regular user numbers who are enabled to open the phone, up to 200 and also it has up to 150 number for time zone. -
Page 3: Installation
WAFER GSM-KEY REMOTE CONTROL UNIT INSTALLATION !Note! Please read this entire manual before installation Take EXTREME care with the Voltage Power supply at AC/DC12-24V Mustn’t suppy the 110V or 220V to this device,that would damage all board ! If device is connect into electricity, you should take off its cover carefully. - Page 4 WAFER GSM-KEY REMOTE CONTROL UNIT WAFER GSM-KEY PROGRAMMING Fast Teach Button: On the board version of GSM-KEY-ADC, there is a “ Fast Learn Button”. When you want to do the fast program to program your number to the WHL list to GSM-KEY device, you can press the button until the LED light, then use your phone to dial the number of GSM-KEY, when pickup the calling,the Teach LED would flash,reject the calling and save the phone number into the device.
- Page 5 WAFER GSM-KEY REMOTE CONTROL UNIT 9. Log Tab 10. Phone numbers Tab – Add regular phone numbers 200 11. Special phone numbers Tab – Add special phone numbers 750 12. Alarm Phone numbers Tab – Add alarm phone numbers 5 13.
- Page 6 WAFER GSM-KEY REMOTE CONTROL UNIT #WHL White List. This is the command that you will use most. it is used to add or remove numbers that are enabled to open the gate into the White List. You can add up to 200 numbers in the list. Every position must be indicated in the command and we advise you to keep a list written somewhere to know which numbers are in and in which position.
- Page 7 WAFER GSM-KEY REMOTE CONTROL UNIT • To check which is the number in a place of the list: #PWD123456#SHL0001? Acknowledge : SHL01 IS 61143815 OK Or #PWD123456#PHL0001? #PWD123456#QHL0001? • To erase a number: #PWD123456#WHL001=0000 Or #PWD123456#PHL001=0000 #PWD123456#QHL01=0000 (or you can write over it another number you wish to add)
- Page 8 WAFER GSM-KEY REMOTE CONTROL UNIT #PWD123456#ALARM=ALL? Acknowledge : ALARM IS XXXXX:XXXX:XXXXXXX:0000:0000 (Will show total five numbers, if no effective number,that will be replaced with 0000 ) (4) Alarm mode setup There are two alarm input ,you can set at PHONE or SMS...
-
Page 9: Pc Software Interface
PC Software interface: Software language select Select the right language according to your county,wafer will update the language step by setp. (When Distributor need to support your local language,please contact wafer company) COM Port parameters config interface and connect to the device Before program the device through the PC,firstly you need to config the COM port paramters and then connect the device to PC software. - Page 10 WAFER GSM-KEY REMOTE CONTROL UNIT according your program adapter ordered ( you can confirm it from the following program adapter pictures list ) 1. Nomal program mode (RS232 program adapter and USB program adapter) No selection of box of the RF-KEY mode and use modem Input the right password,initial password is “...
- Page 11 WAFER GSM-KEY REMOTE CONTROL UNIT GSM Modem program adapter Phone Numbers Setting interface: (Before download the phone numbers,you need to SET the index to red color,then push the button”Download All Phones”) Special Phones Setting: http://www.waferstar.com...
- Page 12 WAFER GSM-KEY REMOTE CONTROL UNIT Alarm Phone Numbers Setting: Log Interface http://www.waferstar.com...
- Page 13 WAFER GSM-KEY REMOTE CONTROL UNIT Miscellanelous Parameters Setting Page: Unit Info: That is showing the Device edition of the design,you don’t need to change it http://www.waferstar.com...
- Page 14 3. You can use the Relay Status selection box to check if that relay output can work well or not. 4. Battery backup function is not available on the normal Wafer products. http://www.waferstar.com...
-
Page 15: Troubleshooting
· If you use the USB to RS232 adapter,should check the drive is properly installed or not What type of the USB to COM port adapter should order to work with GSM-KEY · That would be better to order WAFER USB adapter · Order the good quality USB adapter with FT232 chip inside GSM-KEY does not communicate with PC ·... - Page 16 This brochure provides an overview of the products and services of WEIFU GSM Modules, For further information and queries kindly contact: Email: wafer@waferstar.com Web: www.waferstar.com Tel: 0086-21-51870528 Also accessible via our online Service Skype: wafer-service If you need any sample order,please check our online store: Http://www.wafer-shopping.com Copyright 2008, WEFU GSM V201312-V5.0 http://www.waferstar.com...