Vend-10, 11 Programming Instructions - Amana A1200S Service

VEND-10, 11 Programming Instructions

!
VEND-10.000, .A
As shipped from the factory, the controller in the oven is
preset to "cook" (Full Power) and standard times as
shown below:
Button Time
1 :10
2 :20
3 :30
4 :45
To reprogram the times you want:
1. Open the oven door; leave it open.
2. Enter the "manager's mode" (programming) code
"614" (push button 6, 1, and 4).
3. Close the oven door, note flashing colons which
indicate you are in the "manager's mode". If one
minute elapses before you push a button, the oven
will shut down. To continue programming, re-enter
the "manager's mode" and begin with the last button
you were programming.
NOTE: For each button to be programmed:
4. Push the button to be reprogrammed. Note that the
button number and programmed time appear in the
display.
5. To change cook times:
Push and hold in button 1
to change seconds
Push and hold in button 2
to change tens of seconds
Push and hold in button 3
to change minutes
Push and hold in button 4
to change tens of minutes
NOTE: If you miss the number you want, continue to
hold. Momentary pushes will advance the count
one number at a time.
6. When you have entered the time you want, push
button 5.
7. Push the button to be reprogrammed, then push the
defrost button. The defrost button is located behind
the ** symbol. The defrost time previously
programmed will appear in the display (blank = 0
defrost time).
8. To change defrost time:
Push and hold in button 1
to change seconds
Push and hold in button 2
to change tens of seconds
Push and hold in button 3
to change minutes
Push and hold in button 4
to change tens of minutes
WARNING
Button Time
5 1:00
6 1:30
7 2:00
"00:01"
"00:10"
"01:00"
"10:00"
"00:01"
"00:10"
"01:00"
"10:00"
To avoid risk of electrical shock, personal injury, or death,
disconnect power to unit and discharge the capacitor
before following any disassembly procedures.
NOTE: If you miss the number you want, continue to
hold. Momentary pushes will advance the count
one number at a time.
9. When you have entered the time you want, push
button 5.
10. If you want to reprogram another button, repeat steps
4 through 9.
11. When you have completed programming the buttons
you wish to change, open and close the oven door to
exit the "manager's mode" and go back to normal
operation.
NOTE: If you programmed a "defrost" time and a
"cook" time on the same button, that button will
provide "two-stage" cooking.
Example: If you select 2:00 of "defrost" plus 1:00 of "cook"
time on a button. The total cycle time will equal time will
equal 3:00 for that button. The oven will defrost for two
minutes and heat the food from frozen to ready per your
instructions.
"Cook Count"
To use the "Cook Count" feature:
1. Open the oven door; leave it open.
2. Enter the access code "613" to begin the "Cook
Count" mode (push buttons 6, 1, and 3).
3. Close the oven door.
4. The oven display will show "C:" for count and will
provide the total number of heating cycles for all ten
buttons combined. The left 4 digits will be displayed
for three seconds followed by the right 3 digits.
Example:
"0045" for three seconds
"Blank" for two seconds
"817" for three seconds
In this example, the total number of heating cycles on all
buttons is 45, 817.
5. Push each button to obtain the count for that specific
button.
Example:
Push button 4, note button 4 in the display.
Display shows left 3 digits for three seconds:"003".
Blank for two seconds.
Display shows right 3 digits for three seonds:"247".
The count for button 4 is 3,247 heating cycles.
6. After obtaining the counts, open the oven door to exit
the "Cook Count" mode or let the oven shut itself
down (in 60 seconds)
41 RE220002 Rev. 6