Amana A1200S Service page 42

VEND-10, 11 Programming Instructions
!
VEND-10.B
As shipped from the factory, the controller in the oven is
preset to one second of defrost time plus full power time
to equal the standard times as shown below:
Button Time
1 :10
2 :20
3 :30
4 :45
Any button may be programmed for:
• Heating items from 1 second to 39 minutes and 59
seconds (:01 to 39:59).
• Defrost II time from 1 second to 39 minutes and 59
seconds (:01 to 39:59).
• "Two Stage" cooking - Defrost II (up to 39:59) followed
by full power heating (up to 39:59). This allows you to
defrost and reheat food to serving temperature with a
single button push.
To reprogram the times you want:
1. Open the oven door; leave it open.
2. Enter the programming code "614" (push buttons 6, 1
and 4).
3. Close the oven door, note "PROG" in the display
which indicates you are in the programming mode.
4. Push the button to be reprogrammed. Note that the
button number and the defrost programmed time
appear in the display.
5. The change times:
Push and hold in button 1
to change seconds
Push and hold in button 2
to change tens of seconds
Push and hold in button 3
to change minutes
Push and hold in button 4
to change tens of minutes
NOTE: If you miss the number you want, continue to
hold. Momentary pushes will advance the count
one number at a time.
NOTE: A minimum of one second of defrost time must
be entered in the first stage of each button.
6. Push button 5. The display will show the previously
set second stage time.
7. To change second stage time, repeat step 5 above.
8. Push button Programming of the button is complete.
Example: If you select 2:00 of "Defrost II" plus 1:00 of full
power on a button, the total cycle time will equal 3:00 for
that button. The oven will defrost for two minutes and heat
for one minute to heat the food from frozen to ready, per
your instructions.
RE220002 Rev. 6`
WARNING
Button Time
5 1:00
6 1:30
7 2:00
"00:01"
"00:10"
"01:00"
"10:00"
To avoid risk of electrical shock, personal injury, or death,
disconnect power to unit and discharge the capacitor
before following any disassembly procedures.
9. Go back to step 4 for the next button to be
programmed.
10.When you have completed programming the buttons
you wish to change, open and close the oven door to
exit the programming mode and go back to normal
operation.
Cook Count
To use the "Cook Count" feature:
1. Open the oven door; leave it open.
2. Enter the access code "613" to begin the "Cook
Count" mode (push buttons 6, 1, and 3).
3. Close the oven door.
4. The oven display will show "Count" and will provide
the total number of heating cycles for all 7 buttons
combined.
5. Push each button to obtain the count for that specific
button.
6. After obtaining the counts, open the oven door to exit
the "Cook Count" mode and revert to normal
operation.
Volume Adjustment for End-of-Cook Cycle
Tone
1. Open the oven door; leave it open.
2. Press button 6, 1 and 6.
3. Close the door and "Off", "Low", "Medium", or "High"
will appear in the display.
4. To change volume to "Off" press button 1.
To change volume to "Low" press button 2.
To change volume to "Medium" press button 3.
To change volume to "High" press button 4.
5. Open and close the oven door to revert to normal
operation.
VEND-10.C, .F., .G, .H, .J, .K, .L
As shipped from the factory, the controller in the oven is
preset to 100% power and standard times as shown
below:
Button Time
1 :10
2 :20
3 :30
4 :45
5 :50
(10 is shown as 0 on panel)
42
Button Time
6 1:00
7 1:15
8 1:30
9 1:45
10 2:00