Table of Contents
Advertisement
Quick Links
Contents
Appliance Registration
Consumer Services
Control Settings
Energy Saver Stitch
Extension Cords
Model
and
Serial
Numbers
Problem Solver
Warranty
Back Cover
GE Answer Center@
800.626.2000
Models AMD1O
AMD12
GE Appliances
Room Air Conditioner
2
6
6
6
15
4,5
5
7
4
8-14
2,6
7
2
6
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for GE AMD10
Summary of Contents for GE AMD10
-
Page 1: Table Of Contents
Air Filter Grille & Cabinet Outdoor Coil Consumer Services Control Settings Electrical Requirements Energy Saver Stitch Extension Cords Grounding Installation Instructions 8-14 Model Serial Numbers Problem Solver User’Maintenance Instructions Warranty Back Cover GE Answer Center@ 800.626.2000 Models AMD1O AMD12 GE Appliances... -
Page 2: Help Us Help You
In most intended purpose as described cases, this will solve the problem. Consumer Affairs in this Use and Care Guide. GE Appliances NEXT, if you are still not pleased, Appliance Park write all the details—including This air conditioner must be Louisville, KY 40225 your phone number—to:... -
Page 3: Adapter Plug
Electrical Read Carefully. How to connect that mates respectively with a 230/208-volt perpendicular, electricity tandem or large tandem type wall outlet. These types of outlets are available at most hardware stores. For personal safety, this appliance mu;t be properly grounded. Electrical requirements 115-volt models require a 115/120- MATCHING... -
Page 4: Selector Switch
Operating Your Air Conditioner Controls SELECTOR THERMOSTAT LOW COOL \\\\ ’’.’ ’/////,,,,.+cooL COOLER ~ ONLY ‘ 2 3 4 5 6 7 8 9 10 OFF , COOL MANUAL HOUR Selector Switch Thermostat Control Timer Control OFF turns air conditioner off. When you move the Thermostat When you turn the Timer Control to the MANUAL setting, the air... -
Page 5: Air Direction
For nighttime operation Energy Saver Fan For normal cooling Cycle Switch During the cooler evening hours, w 1. Set the Selector Switch at HIGH recommend that you set the Selecto COOL. Switch at LOW COOL for quieter ENERGY 2. Set the Thermostat Control at operation and the Thermostat the desired number (usually 5-7 is a Control at mid-range (5 or 6). -
Page 6: Care And Cleaninp
GE service outlet. accumulated dust and lint. If the filter is very dirty, use a mild Front Grille... - Page 7 Moisture removed from indoor air drains to rear of cabinet where it is picked up by a fan and thrown against the outdoor condenser coil. If you need more help...call, toll free: GE Answer Center@ 800.626.2000 consumer information service...
-
Page 8: Electrical Requirements
INSTALLATION INSTRUCTIONS WINDOW REQUIREMENTS BEFORE YOU BEGIN Standard double-hung window with actual Read these instructions completely and opening width of 26” to 42”. carefully. bottom of sash to stool. and ordinances. Install the air conditioner in a window where there will be enough clearance around the cabinet instructions with the consumer. - Page 9 TOOLS NEEDED SCREWS FURNISHED (see samples) Phillips head screwdriver Type A Type B Type C Type D Blade-type screwdriver Sharp knife or razor blade Rule or tape measure Pencil Level Box wrench Qty-3 Qty-2 Qty-4 Qty-6 (continued next page)
- Page 10 REMOVEFRONTGRILLE PREPARE CABINET See Front Grille section. mounting rail Room side + PREPARE CHASSIS. 1. Remove chassis locking bracket and chassis locking screw with a Phillips head screwdriver. Type D screw (Save for reuse.) 1. Install top mounting rail onto top of cabinet with 3 Type D screws.
- Page 11 Secure top mounting rail with two Type B screws. 1. Slide left window filler panel into top and bottom mounting rails. 2. Slide retainer panel into window filler panel and attach to cabinet with 2 Type C screws. 3. Repeat for right side. Top mounting rail Window —...
- Page 12 WINDOW INSTALLATION (Continued) Seal small openings around cabinet with gum-type Slide chassis into cabinet. (Make sure tubing on sealer, provided. unit is not touching wall case.) 2. Lock chassis into cabinet by reinstalling chassis locking bracket and chassis locking screw removed in Step 2.
-
Page 13: Tools Required
THROUGH-THE-WALL INSTALLATION THE CABINET BE INSTALLED PREPARE WALL OPENING. THROUGH THE WALL IN BOTH EXISTING BUILDINGS CONSTRUCTION. Measure width and height of cabinet and add 1/8” to each dimension. Any side louvers must project on the oudoor side of the wall. The room side of the cabinet must project into the room at least 1“... - Page 14 THROUGH-THE-WALL INSTALLATION (cont,n.e~, (continued). Secure cabinet sides to wooden frame with six 1“ long #1 O wood screws and secure cabinet top Trim to frame with four 1“ long #1 O wood screws. Molding (if desired) Holes for #10 1“ Long INSIDE Wood Screws Flashing...
-
Page 15: User'maintenance Instructions
With the purchase of your new GE appliance, receive the assurance that if you ever need information or assistance from GE, wdll be there. All you have to do is call–toll-free! major appliance, GE Arrswel (;enter”’ help. YOLlr call-and yoLIr questiorr-... - Page 16 Attorney General. Warrantor: General Electric Company If further help is needed concerning this warranty, write: Manager—Consumer Affairs, GE Appliances, Louisville, KY 40225 AMD1O Pub No. 49-7264 11-91 CG...
Need help?
Do you have a question about the AMD10 and is the answer not in the manual?
Questions and answers