Safety Measures; Using The Blender - Melissa 646-047/48 User Manual

INTRODUCTION
To get the most from your new candyfloss machine, please read
through these instructions carefully before using it for the first
time. We also recommend that you keep the instructions for
future reference, so that you can remind yourself of the functions
of the appliance.

SAFETY MEASURES

Normal use of the blender
• Incorrect use of the blender may cause personal injury and
damage to the blender.
• Use the blender for its intended purpose only. The manu-
facturer is not responsible for any injury or damage resulting
from incorrect use or handling (see also Guarantee Terms).
• The blender may only be connected to 230 V, 50 Hz.
• The base of the blender or cord must not be submerged in
water or any other liquid.
• Do not operate with wet or damp hands. Make sure that no
liquid gets into the base.
• Never leave the blender unattended when in use and keep an
eye on children.
• The blade must be handled with care, as it is extremely sharp.
• NEVER insert your fingers, kitchen utensils or similar into the
blender jug while the blender is running or is connected to the
mains.
• Never remove the lid or filler cap from the blender jug while
the blender is running.
• Do not leave the blender running for more than 1 minute at a
time. If it has been running for 1 minute, you should leave it to
cool down before using it again.
• Never use the blender if the jug is empty.
• Not suitable for commercial or outdoor use.
Positioning the blender
• Always place the blender at the back of the kitchen counter.
• Do not place the blender next to hot areas, for example gas
rings and electric hotplates.
• Do not allow the cord to hang over the edge of a table/
counter, and keep it away from hot objects and naked flames.
Cord, plug and mains socket
• Ensure that the cord is fully extended.
• Check regularly that the cord and plug are not damaged and
do not use the blender if they are, or if it has been dropped or
damaged in any other way.
• If the blender, cord or plug is damaged, the blender must be
inspected and, if necessary, repaired by an authorised repair
engineer, otherwise there is a risk of electric shock. Never try
to repair the blender yourself.
• Unplug the blender before replacing the blender jug with the
coffee/spice mill and vice versa, before removing the lid from
the jug or the mill, before cleaning, and when the blender is
not in use.
• Avoid pulling the cord when removing the plug from the
socket. Instead, hold the plug.
• Check that it is not possible to pull or trip over the blender
cord or any extension cord.
UK
KEY TO THE BLENDER PARTS
1. Release button for jug lid
2. Filler cap
3. Jug lid
4. Blender jug
5. Blade
6. Blender shaft
7. Base
8. On/Off button
9. Coffee/spice mill (646-048)
10. Mill lid (646-048)
PRIOR TO FIRST USE
Place the base (7) on a flat surface, e.g. a kitchen counter, and
make sure it is standing firmly on the four suckers underneath.
Before using the blender for the first time, or after prolonged
storage without use, wash any parts that will come into contact
with food.

USING THE BLENDER

General operation
• Fit the blender jug (4) or coffee/spice mill (9), and put the
ingredients to be blended in it as described below.
• Start the blender by turning the on/off button (8) to position
"1" or "2" and switch it off by turning it back to position "0".
• To use the blender in short bursts, turn the on/off button to
position "Pulse". The blender will run at top speed as long as
you hold the button down in that position, and will stop when
you release the button, which then automatically reverts to
position "0".
• You should stop the blender at regular intervals to check
whether the ingredients have been sufficiently blended/chop-
ped.
Using the blender jug
1. Attach the blender jug to the blender shaft (6) with the handle
facing you and to the right, and turn it anticlockwise until it
locks into place.
2. Place the food in the blender jug.
3. Fit the jug lid (3) by placing it over the blender with the pin
to the right of the handle and turning the lid clockwise until it
locks into place.
4. Fit the filler cap (2) by inserting it into the hole in the lid so the
pins on the cap fit into the grooves in the lid. Turn the cap
clockwise until it locks into place.
5. Start the blender.
10