Chassis Tightening Torques - Yamaha RAPTOR YFM125RA Service Manual

EAS20350

CHASSIS TIGHTENING TORQUES

Item
Engine bracket (upper side) and
frame bolt
Engine bracket (upper side) and
engine nut
Engine bracket (front side) and
engine nut
Engine and frame nut
Engine bracket (front side) and
frame bolt
Swingarm pivot shaft and frame
nut
Swingarm and drive chain guide
bolt
Rear shock absorber assembly
and frame nut
Rear shock absorber and swing-
arm nut
Rear shock absorber assembly
locknut
Rear axle pinch bolt
Front shock absorber assembly
and frame nut
Front shock absorber assembly
and front lower arm nut
Front upper arm and frame nut
Front lower arm and frame nut
Steering stem and frame nut
Steering stem bushing and frame
bolt
Steering stem and handlebar
holder bolt
Tie-rod end and locknut
Steering knuckle and front wheel
hub nut
Steering knuckle and front arm
nut (upper and lower)
Steering knuckle and tie-rod ball
joint nut
Steering stem and tie-rod ball
joint nut
Fuel tank and fuel cock screw
Fuel tank and frame bolt
Front wheel and front wheel hub
nut
Thread
Q'ty
size
M8 2 33 Nm (3.3 m·kgf, 24 ft·lbf)
M8 1 40 Nm (4.0 m·kgf, 29 ft·lbf)
M8 1 40 Nm (4.0 m·kgf, 29 ft·lbf)
M8 2 44 Nm (4.4 m·kgf, 32 ft·lbf)
M8 4 33 Nm (3.3 m·kgf, 24 ft·lbf)
M14 1 100 Nm (10 m·kgf, 72 ft·lbf)
M6 1 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
M12 1 55 Nm (5.5 m·kgf, 40 ft·lbf)
M12 1 55 Nm (5.5 m·kgf, 40 ft·lbf)
M20 1 42 Nm (4.2 m·kgf, 30 ft·lbf)
M8 4 21 Nm (2.1 m·kgf, 15 ft·lbf)
M10 2 48 Nm (4.8 m·kgf, 35 ft·lbf)
M10 2 48 Nm (4.8 m·kgf, 35 ft·lbf)
M10 2 45 Nm (4.5 m·kgf, 33 ft·lbf)
M10 4 45 Nm (4.5 m·kgf, 33 ft·lbf)
M10 1 35 Nm (3.5 m·kgf, 25 ft·lbf)
M8 2 23 Nm (2.3 m·kgf, 17 ft·lbf)
M8 4 20 Nm (2.0 m·kgf, 14 ft·lbf)
M10 4 15 Nm (1.5 m·kgf, 11 ft·lbf)
M14 2 70 Nm (7.0 m·kgf, 51 ft·lbf)
M10 4 25 Nm (2.5 m·kgf, 18 ft·lbf)
M10 2 25 Nm (2.5 m·kgf, 18 ft·lbf)
M10 2 25 Nm (2.5 m·kgf, 18 ft·lbf)
M6 2 4.0 Nm (0.40 m·kgf, 2.9 ft·lbf)
M6 4 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
M10 8 45 Nm (4.5 m·kgf, 33 ft·lbf)
2-16
TIGHTENING TORQUES
Tightening torque Remarks
See TIP
Use a lock
washer.