Yamaha RAPTOR YFM125RA Service Manual page 38

Item
Drive sprocket cover bolt
Clutch cover bolt
Stator coil lead holder screw
Timing mark accessing screw
Crankshaft end accessing screw
Starter motor lead screw
Starter clutch idle gear holder
screw
Starter motor bolt
Starter clutch bolt
Primary drive gear nut
Clutch spring bolt
Clutch boss nut
Short clutch push rod locknut
Bearing retainer screw
Drive sprocket bolt
Shift pedal bolt
Shift drum segment screw
Stopper lever bolt
Pickup coil bolt
Neutral switch
Neutral switch lead screw
Stator coil bolt
TIP
Cylinder head bolt
1. Apply Yamaha bond No.1215 (Three bond No.1215®) to the threads of the cylinder head bolts
"5", "6".
2. Lubricate the contact surfaces of the cylinder head bolts and on both contact surfaces of wash-
ers with engine oil.
3. Tightening the cylinder head bolts in the proper sequence as shown.
Thread
Q'ty
size
M6 2 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
M6 9 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
M6 1 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
M14 1 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
M32 1 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
M5 1 3.5 Nm (0.35 m·kgf, 2.5 ft·lbf)
M6 2 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
M6 2 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
M8 3 30 Nm (3.0 m·kgf, 22 ft·lbf)
M12 1 70 Nm (7.0 m·kgf, 51 ft·lbf)
M5 4 6 Nm (0.6 m·kgf, 4.3 ft·lbf)
M12 1 60 Nm (6.0 m·kgf, 43 ft·lbf)
M6 1 8 Nm (0.8 m·kgf, 5.8 ft·lbf)
M6 2 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
M5 2 6 Nm (0.6 m·kgf, 4.3 ft·lbf)
M6 1 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
M6 1 12 Nm (1.2 m·kgf, 8.7 ft·lbf)
M6 1 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
M6 2 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
M10 1 9 Nm (0.9 m·kgf, 6.5 ft·lbf)
M4 1 1.3 Nm (0.13 m·kgf, 0.94 ft·lbf)
M6 3 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
2-15
TIGHTENING TORQUES
Tightening torque Remarks
Stake
LT
LT
LT
LT
LT