Table of Contents
Advertisement
Quick Links
Copyright © 2002 The Stanley Works
OPS USA & CE Version
25077
7/2002 Ver. 2
User's Manual
®
DL09
Hydraulic Drill
This Manual Covers The Following Models:
(Depth Rod Not Pictured)
DANGER
SERIOUS INJURY OR DEATH COULD RESULT
FROM THE IMPROPER REPAIR OR SERVICE OF
THIS TOOL.
REPAIRS AND/OR SERVICE TO THIS TOOL
MUST ONLY BE DONE BY AN AUTHORIZED AND
CERTIFIED DEALER.
DL09150
DL09152S
DL09152SN
DL09152SUP
DL09172S
DL09172SN
DL09550D
DL0955001
DL09652
DL0965201
Advertisement
Table of Contents
Related Manuals for Stanley DL09652
Summary of Contents for Stanley DL09652
- Page 1 SERIOUS INJURY OR DEATH COULD RESULT FROM THE IMPROPER REPAIR OR SERVICE OF THIS TOOL. REPAIRS AND/OR SERVICE TO THIS TOOL Copyright © 2002 The Stanley Works MUST ONLY BE DONE BY AN AUTHORIZED AND OPS USA & CE Version CERTIFIED DEALER.
-
Page 2: Table Of Contents
It is the responsibility of the operator and not be copied in whole or in part without service technician to read rules and the prior written consent of The Stanley Works. This exception does not permit instructions for safe and proper operation copies to be made for others, whether or and maintenance. -
Page 3: Certificate Of Conformity
Directive: Approved body: EN28662-1 EN ISO 3744 2001 Date: Date of expiration: None 6. Special Provisions: Stanley Hydraulic Tools, Milwaukie, Oregon USA 2002 Done at: Date: Engineering Manager Signature: Position: Specifications Drive Size______ 1/2 in./ 1.3 cm 3-Jaw Adjustable Drill Torque___20 ft lbs / 27 Nm at 2000 psi/ 140 bar... -
Page 4: General Safety Instructions
Do not exceed the rated limits of the tool or use the tool for applications beyond its design capacity. Always keep critical tool markings, such as labels and warning stickers legible. Always replace parts with replacement parts recommended by Stanley Hydraulic Tools. Check fastener tightness often and before each use daily. -
Page 5: Tool Decals And Tags
A model sticker is attached to the tool. Never exceed the flow and pressure levels specified on this sticker. The information listed on the DL09 model sticker must be legible at all times. Replace this sticker if it becomes worn or damaged. A replacement is available from your local Stanley distributor. 28323 “CE” Decal... -
Page 6: Hydraulic Hose Requirements
HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hoses purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS. If the information in a tag is illegible because of wear or damage, replace the tag immediately. A new tag may be obtained at no charge from your Stanley Distributor. -
Page 7: Htma Requirements
HTMA Requirements NOTE: These are general hydraulic system requirements. See tool specification page for tool specific requirements. Tool Category Hydraulic System 20Lpm at 138bar 30Lpm at 138bar 40Lpm at 138bar BHTMA CATEGORY BHTMA CATEGORY EHTMA CATEGORY Type III Type II Requirements Type I Flow rate... -
Page 8: Hydraulic Recommendations
D.T.E. 13 likely in cool-operating hydraulic Circuits. Gulf “Harmony” AW-HVI-1 50-32 These fluids are recommended by Stanley Hydraulic Tools for use in Shell “Lo-Hydraul” 32 our tools. Other fluids that meet or exceed the specifications of these “Sunvis” 805 MG fluids may also be used. -
Page 9: Operating Instructions
Operating Instructions CAUTION NOTE: If uncoupled hoses are left in the sun, pressure increase inside the hose Make certain that the chuck has been securely mounted. may result in making them difficult to connect. Whenever possible, connect the Check Power Source free ends of the hoses together. -
Page 10: Cold Weather Operation
Operating Instructions Cold Weather Operation Damage to the hydraulic system or tool can result from use with fluid that is too viscous or thick. If the tool is to be used during cold weather, preheat the hydraulic fluid at low engine speed. Follow steps 1 through 5 (connect hoses) page # 9 of the operating instructions. -
Page 11: Troubleshooting
Troubleshooting This section describes how to find and resolve problems users may experience. If a situation occurs that is not covered, call your Stanley Customer Service representative for assistance. WARNING Inspecting the tool or installing parts with the hydraulic hoses connected can result in severe personal injury or equipment damage. - Page 12 Troubleshooting Symptom Possible Cause Solution Oil gets hot, Open center tool on a closed center Use tools to match circuit. power unit circuit and vice versa. working hard. Circuit relief set too low. Adjust relief valve to 2100 psi/ 145 bar.
-
Page 13: Parts Illustration
DL09 Parts Illustration... -
Page 14: Parts List
DL09 Parts List NOTE: Part Number Description when ordering. Item Part Part Description Description Qty. 38676 Depth Guage Rod (ModelsDL09172S,DL09172SN, & DL09152S Only)Shipped uninstalled. 38685 Thumb Screw (ModelsDL09172S,DL09172SN, & DL09152S Only)Shipped uninstalled. 15211 Danger Sticker (Not used on Models DL0955001 & DL0965201 08175 Ball Bearing 26655... - Page 15 DL09150, DL0955001 , & DL09550D ONLY) 28234 Hose Whip (Not Used On Models DL09150, DL0955001 , & DL09550D) 24058 Female Coupler Body 3/8”(Not Used On Models DL09150, DL09550D, DL09652 & DL0955001 03972 Female Coupler Body (Used On Model DL0955001 ONLY) 24059 Male Coupler Body 3/8”(Not Used On Models...
-
Page 16: Warranty
Stanley Hydraulic Tools (hereinafter called “Stanley”), subject to the exceptions contained below, warrants new hydraulic tools for a period of one year from the date of sale to the first retail purchaser, or for a period of 2 years from the shipping date from Stanley, whichever period expires first, to be free of defects in material and/or workmanship at the time of delivery, and will, at its option, repair or replace any tool or part of a tool, or new part, which is found upon examination by a Stanley authorized service outlet or by Stanley’s factory in Milwaukie, Oregon to be DEFECTIVE IN... - Page 17 For additional Sales & Service information, contact: ® Stanley Hydraulic Tools Division of the Stanley Works 3810 SE Naef Road Milwaukie, OR 97267 USA Tel: (503) 659-5660 Fax: (503) 652-1780...