Tool Decals And Tags - Stanley DL09652 User Manual

A model sticker is attached to the tool. Never exceed the flow and pressure levels specified on this
sticker. The information listed on the
sticker if it becomes worn or damaged. A replacement is available from your local Stanley
distributor.
28323
"CE" Decal
(CE Models only)
28788
Manual Sticker
(Not used on all models)
15211
Danger Sticker
DANGER
Failure to use hydraulic hose labeled and certified as 7-10 GPM/ 24-36 LPM
non-conductive when using hydraulic tools on or
DO NOT EXCEED 2000 PSI/ 140 BAR
near electric lines may result in death or serious
n DO NOT EXCEED SPECIFIED FLOW OR PRESSURE.
injury. TOOL ON CLOSED-CENTER SYSTEM. n USEOPEN-CENTER TOOL ON OPEN-
CENTER SYSTEM. n CORRECTLY CONNECT HOSES TO TOOL "IN" AND "OUT"
PORTS. n IMPROPER HANDLING, USE OR MAINTENANCE OF TOOL COULD
For proper and safe operation read owners manual
RESULT INA LEAK, BURST OR OTHER TOOL FAILURE.
and make sure that you have been properly trained in
OR BURST CAN CAUSE OIL INJECTION INTO THE BODY.
correct procedures required for work on or around
ELECTROCUTION
OBSERVE THESE PRECAUTIONS CAN RESULT IN SERIOUS PERSONAL
electric lines.
HAZARD
INJURY.
The SAFETY TAG, P/N 15875, shown at right, smaller
than actual size, is attached to the tool when shipped
from the factory. Read and understand the safety
instructions listed on this tag before removal. We
suggest you retain this tag and attach it to the tool
when not in use.
DL09 model sticker must be legible at all times. Replace this
n USE CLOSED-CENTER
n CONTACT AT A LEAK
n FAILURE TO
Tool Decals & Tags
DANGER
1. FA I LU R E T O U S E H Y D RAU L I C H O S E L A B E L E D A N D
C E R T I - F I E D A S N O N - C O N D U C T I V E W H E N U S I N G
HYDRAULIC TOOLS ON OR NEAR ELECTRICAL LINES
MAY RESULT IN DEATH OR SERIOUS INJURY.
B E F O R E U S I N G H O S E L A B E L E D A N D C E R T I F I E D A S
N O N - C O N D U C T I V E O N O R N E A R E L E C T R I C L I N E S .
BE SURE THE HOSE IS MAINTAINED AS NON- CONDUCTIVE . THE
HOSE SHOULD BE REGULARLY TESTED FOR ELECTRIC CURRENT
LEAKAGE IN ACCORDANCE WITH YOUR SAFETY DEPARTMENT
INSTRUCTIONS.
2. A H Y D R A U L I C L E A K O R B U R S T M AY C A U S E O I L
INJECTION INTO THE BODY OR CAUSE OTHER SEVERE PERSONAL
INJURY.
A. D O N O T E X C E E D S P E C I F I E D F L O W A N D
P R E S S U R E F O R T H I S T O O L . E X C E S S F LO W O R
PRESSURE MAY CAUSE A LEAK OR BURST.
B. D O N O T E X C E E D R AT E D W O R K I N G P R E S S U R E
O F H Y D R A U L I C H O S E U S E D W I T H T H I S T O O L .
E X C E S S P R E S S U R E M A Y C A U S E A L E A K O R
BURST.
C. C H E C K T O O L , H O S E , C O U P L E R S
C O N N E C T O R S D A I L Y F O R
L E A K S . D O N O T F E E L F O R L E A K S W I T H
Y O U R H A N D S . C O N T A C T W I T H A L E A K M A Y
RESULT IN SEVERE PERSONAL INJURY.
IMPORTANT
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE
OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY TOOL
OPERATOR.
SEE OTHER SIDE
(517) 15875
29149
Rotation Direction Sticker
(Not used on all models)
Stanley Hydraulic Tools
3810 SE Naef Rd
® Milwaukie, Oregon 97267
Model No. 15-45 lpm/4-12 gpm
DL09 140 bar/2000 psi
28769
DL09 Model Sticker
RPM Sticker
29148
(Not used on all models)
30Lpm at 138bar
BHTMA CATEGORY
11207
Circuit Type "D" Decal
(Not used on all models)
DANGER
D. DO NOT LIFT OR CARRY TOOL BY THE HOSES. DO NOT ABUSE
HOSE. DO NOT USE KINKED, TORN OR DAMAGED HOSES.
3. M A K E S U R E H Y D R A U L I C H O S E S A R E P R O P E R LY
C O N N - E C T E D T O T H E T O O L B E F O R E P R E S S U R I Z I N G
S Y S T E M . S Y S T E M P R E S S U R E H O S E M U S T A LWAY S
B E C O N N E C T E D T O T O O L " I N " P O R T. S Y S T E M
R E T U R N H O S E M U S T A LW AY S B E C O N N E C T E D AT
T O O L " O U T " P O RT. R E V E R S I N G C O N N E C T I O N S M AY
C A U S E R E V E R S E T O O L O P E R AT I O N W H I C H C A N
CAUSE SEVERE PERSONAL INJURY.
4. D O N O T C O N N E C T C L O S E D - C E N T E R T O O L S T O
O P E N - C E N T E R H Y D R A U L I C S Y S T E M S . T H I S M A Y
C A U S E E X T R E M E S Y S T E M H E AT A N D / O R S E V E R E
PERSONAL INJURY.
DO NOT CONNECT OPEN-CENTER TOOLS TO C LO S E D - C E N T E R
HYDRAULIC SYSTEMS. THIS MAY RESULT IN LOSS OF OTHER
HYDRAULIC FUNCTIONS POWERED BY THE SAME SYSTEM AND/OR
SEVERE PERSONAL INJURY.
5. B Y S TA N D E R S M A Y B E I N J U R E D I N Y O U R W O R K
A R E A . K E E P BY S TA N D E R S C L E A R O F YO U R W O R K
AREA.
&
6. WEAR HEARING, EYE, FOOT, HAND AND HEAD PROTECTION.
7. TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE, ALL TOOL
REPAIR, MAINTENANCE AND SERVICE MUST BE
PERFORMED BY AUTHORIZED A N D P R O P E R LY
TRAINED PERSONNEL.
IMPORTANT
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE
OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY TOOL
OPERATOR.
SEE OTHER SIDE
(517) 15875
5