Sony PXW-X200 Operating Instructions Manual page 132

For "PAL Area"
MXF
Video format
XAVC-L50 1080/50P
XAVC-L35 1080/50P
XAVC-I 1080/50i
XAVC-L50 1080/50i
XAVC-L35 1080/50i
XAVC-L25 1080/50i
XAVC-I 1080/25P
XAVC-L50 1080/25P
XAVC-L35 1080/25P
HD422 50/1080/50i
HQ 1920×1080/50i
HQ 1440×1080/50i
HD422 50/1080/25P
HQ 1920×1080/25P
HQ 1440×1080/25P
XAVC-I 720/50P
XAVC-L50 720/50P
HD422 50/720/50P
HQ 1280×720/50P
HD422 50/720/25P
IMX50 50i SQ/EC
IMX50 25P SQ/EC
DVCAM 50i SQ/EC
DVCAM 25P SQ/EC
MP4
Video format
HQ 1920×1080/50i
HQ 1440×1080/50i
SP 1440×1080/50i
HQ 1920×1080/25P
HQ 1440×1080/25P
HQ 1280×720/50P
HQ 1280×720/25P
AVI
Video format
DVCAM 50i SQ/EC
DVCAM 25P SQ/EC
The phase adjustment for the reference signal can
also be made with "Genlock" (page 120) of the
OTHERS menu.
132 External Synchronization
Valid reference
signal
1080/50i
PAL
1080/50i
720/50P
PAL
1080/50i
PAL
Valid reference
signal
1080/50i
PAL
1080/50i
720/50P
PAL
Valid reference
signal
1080/50i
PAL
Notes
• When the output format is SD Mode and you use one
of the video formats below, genlock is not possible. Set
the video format to HD Mode.
MXF: XAVC-I 720/59.94P
XAVC-L50 720/59.94P
HD422 50/720/59.94P
HQ 1280×720/59.94P
XAVC-I 720/50P
XAVC-L50 720/50P
HD422 50/720/50P
HQ 1280×720/50P
MP4: HQ 1280×720/59.94P
HQ 1280×720/50P
• If the reference signal is unstable, genlock is not
possible.
• The subcarrier is not synchronized.
Synchronizing the timecode of your
camcorder with that of another unit
Set the unit that supplies the timecode to a mode
in which the timecode output keeps advancing
(Free Run or Clock mode).
1
Set "Timecode" of the TC/UB SET
menu as follows:
Mode: Preset
Run: Free Run
2
Press the DURATION/TC/U-BIT
button (page 10) so that the timecode is
displayed on the screen.
3
Confirm that the IN/OUT switch (page
12) is set to IN, then supply an HD or SD
reference video signal to the
GENLOCK IN connector and the
reference timecode to the TC IN
connector.
The built-in timecode generator of your
camcorder locks to the reference timecode, and
the message "EXT-LK" is displayed on the
screen.
About 10 seconds after locking, even if the
reference timecode from the external device is
disconnected, the external lock will be kept.
Notes
• Check that the reference timecode and the reference
video signal are in a phase relation that complies the
SMPTE timecode standards.
• When you finish the above procedure, the timecode is
immediately synchronized with the external timecode,
and the time data indication will show the value of the
external timecode. However, wait for a few seconds