Toshiba VF-PS1 Instruction Manual page 198

Parameter setting
Positive
logic



















7




















Note 1: "ON" in positive logic
"OFF" in positive logic : Open collector output transistor or relay is turned off.
"ON" in negative logic : Open collector output transistor or relay is turned off.
"OFF" in negative logic : Open collector output transistor or relay is turned on.
Note 2: Alarm output check conditions are as follows.
(1) Undervoltage detected :To be checked during operation.
(2) Low current detected
(3) Overtorque detected
Sink logic/source logic
Sink logic and source logic (logic of input/output terminal) can be switched to each other.
⇒ For details, refer to Section 2.3.2.
Negative Function
logic
Specified data output 4

Specified data output 5

Specified data output 6

 Specified data output 7
Positive torque limit

Negative torque limit

Output for external rush

suppression relay
L-STOP

 Part replacement alarm
Over-torque pre-alarm

Frequency command 1/

2 selection
Failure FL (Except

emergency stop)
Local/remote switching

 Forced operation (Force)
Forced operation (Force) ON: Forced operation

 Undertorque detection
Frequency command
 agreement signal
(RR/S4)
Frequency command

agreement signal (VI)
Frequency command

agreement signal (RX)
 PTC alarm detection
Power removal signal

 VI/VII input wire breakage ON: If the breakage of a VI/VII input wire is detected
My function output 1

 My function output 2
My function output 3

My function output 4

My function output 5

My function output 6

 My function output 7
My function output 8

 My function output 9
My function output 10

 My function output 11
My function output 12

My function output 13

My function output 14

My function output 15

 My function output 16
Always OFF (for terminal

signal tests)
: Open collector output transistor or relay is turned on.
: To be checked during operation command.
: To be checked always.
Operation output specifications (in case of positive logic)
Output of the designated data in 7-bit.
ON:Positive torque is over the positive torque limit level.
ON:Negative torque is over the positive torque limit level.
ON:External rush suppression relay is actuated.
ON:Operation at the lower limit frequency is performed
continuously.
Alarm:The time of replacement of parts is approaching.
ON:Over-torque is detected.
ON:Frequency command selection 2 is selected.
ON:A trip other than emergency stop has occurred.
ON: Local mode
ON: Forced operation (Operation continued in the case of a minor
failure)
ON: If an undertorque is detected
ON: If the frequency command specified with  or 
agrees with the frequency command entered via RR/S4 (when RR
is used as a signal input terminal). An agreement range can be
specified with  .
ON: If the frequency command specified with  or 
agrees with the frequency command entered via VI. An agreement
detection range can be specified with  .
ON: If the frequency command specified with  or 
agrees with the frequency command entered via RX An
agreement detection range can be specified with  .
ON: If the PTC thermal specified with  or  is
detected
ON: When a PWR input signal is received
ON:My function output 1 is ON.
ON:My function output 2 is ON.
ON:My function output 3 is ON.
ON:My function output 4 is ON.
ON:My function output 5 is ON.
ON:My function output 6 is ON.
ON:My function output 7 is ON.
ON:My function output 8 is ON.
ON:My function output 9 is ON.
ON:My function output 10 is ON.
ON:My function output 11 is ON.
ON:My function output 12 is ON.
ON:My function output 13 is ON.
ON:My function output 14 is ON.
ON:My function output 15 is ON.
ON:My function output 16 is ON.
Output signal always OFF
G-8
E6581386