Denon AVR-2311 Owner's Manual page 64

ENGLISH
Manual Setup
Setting items
Distance Default : The "Distance" settings are returned to the default settings.
(Continued) • Yes : Reset to the defaults.
• No : Do not reset to the defaults.
When you select "Default" and press
prompt is displayed. Select either "Yes" or "No", and press
Test Tone Start : Output test tone.
Channel Level
Set the volume of the test • Front L / F.Height L / Center / F.Height R / Front R / Surround R /
tone to be the same when it S.Back R
is output from each speaker. z When the "Speaker Config." – "S.Back" setting (vpage 59) is set to
"1spkr", "S.Back" is displayed.
• –12.0dB – +12.0dB (0.0dB) : Adjust the volume.
• When
"Subwoofer" setting switches to "OFF".
• When "Channel Level" is adjusted, the adjusted values are set for all the
surround modes. To adjust the channel level separately for the different
surround modes, use the operation see page 40.
NOTE
• Speakers set to "None" in the "Speaker Config." (vpage 58) settings
are not displayed.
• When a headphones jack is inserted in the PHONES jack of this unit, the
"Channel Level" is not displayed.
Default : The "Channel Level" settings are returned to the default settings.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
When you select "Default" and press
prompt is displayed. Select either "Yes" or "No", and press
60
Remote control operation
buttons
Setting details
ENTER
, the "Default Setting?"
z z
/ S.Back L / Surround L / Subwoofer : Select the speaker.
o
is pressed while the subwoofer volume is set to "–12 dB", the
ENTER
, the "Default Setting?"
Move the cursor
(Up/Down/Left/Right)
Setting items
Crossover Frequency Crossover : Set the crossover frequency.
Set the maximum frequency • 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
of the bass signal output
from each channel to
Advanced : Specify crossover frequency for each speaker.
the subwoofer. Set the
ENTER
.
• Front / Center / Surround / S.Back / F.Height : Select the speaker.
Crossover Frequency to
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
suit the bass reproduction
capability of the speaker
being used.
• "Crossover Frequency" can be set when the "Bass Setting" – "SW
• Always set the crossover frequency to "80Hz". When using small
• For speakers set to "Small", sound below the crossover frequency
• The speakers that can be set when "Advanced" is selected differ
2
Front Speaker Setup
Set the front speakers to
pure direct play modes (2 channel) are set in advance.
use for every surround
• A：Front speaker A is used.
mode.
• B：Front speaker B is used.
• A+B：Both front speakers A and B are used.
ENTER
.
NOTE
MULTI CH : The front speakers used in modes other than the direct,
This can be set when "Amp
stereo and pure direct play modes (2 channel) are set in advance.
Assign" is set to "Front B"
• A：Front speaker A is used.
(vpage 58).
• B：Front speaker B is used.
• A+B：Both front speakers A and B are used.
Confirm the setting
Setting details
250Hz
250Hz : Set the crossover frequency.
Mode" (vpage 59) setting is "LFE+Main", or when you have a speaker
that is set to "Small".
speakers, however, we recommend setting the crossover frequency to
a higher frequency.
is cut from the sound output. The cut bass sound is output from the
subwoofer or front speakers.
depending on the "SW Mode" setting (vpage 59).
• When "LFE" is selected, speakers set to "Small" at "Speaker Config."
can be set. If the speakers are set to "Large", "Full Band" is displayed
and the setting cannot be made.
• If set to "LFE+Main", this setting can be made regardless of the
speaker size.
CH DIRECT/STEREO : The front speakers used in the direct, stereo and
Return to previous menu