Denon AVR-2311 Owner's Manual page 59

n Audyssey Settings
Set MultEQ ® , Dynamic EQ ® and Dynamic Volume ® . These can be selected after Audyssey ® Auto
Setup has been performed. For additional information on Audyssey technology, please see page 82.
NOTE
If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup,
you may not be able to select Dynamic EQ/Dynamic Volume, and "Run Audyssey" may be displayed.
In this case, either perform Audyssey Auto Setup over again or perform "Restore" (vpage 10) to return to
the settings after Audyssey Auto Setup was run.
Setting items
MultEQ Audyssey : Optimize the frequency response of all speakers.
Select one equalizer from Audyssey Byp.L/R : Optimize frequency response of speakers except
three modes. MultEQ front L and R speakers.
corrects both time and Audyssey Flat : Optimize frequency response of all speakers to flat
frequency response response.
problems in the listening Manual : Apply frequency response set with "Manual EQ" (vpage 56).
area based on Audyssey OFF : Turn "MultEQ" equalizer off.
Auto Setup calibration. We
recommend "Audyssey".
• "Audyssey",
MultEQ is the prerequisite
"Audyssey Flat" can be selected after Audyssey
function for Dynamic EQ
Auto Setup has been performed. "Audyssey" is
and Dynamic Volume.
automatically selected after performing Audyssey
Auto Setup. When "Audyssey", "Audyssey Byp.
L/R" or "Audyssey Flat" is selected,
illuminates.
• After running Audyssey Auto Setup, if the
Speaker Configuration, Distance, Channel
Level, and Crossover Frequency have changed
without increasing the number of speakers
measured, only
MULTEQ
• Pressing
NOTE
• "MultEQ" and "Manual" cannot be selected when "EQ Customize" is
set to "Not Used" (vpage 62).
• When using headphones, "MultEQ" is automatically set to "OFF".
Remote control operation
buttons
Default settings are underlined.
Setting details
"Audyssey Byp. L/R" and
illuminates.
makes this setting.
Move the cursor
(Up/Down/Left/Right)
Setting items
Dynamic EQ ®
ON : Use Dynamic EQ.
Solve the problem of OFF : Do not use Dynamic EQ.
deteriorating sound quality
as volume is decreased by
• is displayed when set to "ON".
taking into account human
perception and room
• Buttons on the remote control unit or main unit
acoustics.
can be used for operations.
Works with MultEQ.
GOperations with the remote control unitH
DYN EQ/VOL
Press
DYN EQ/VOL
Each time
below.
Dynamic EQ : ON
Dynamic Volume : Midnight
Dynamic EQ : OFF
Dynamic Volume : OFF
GOperations with the main unitH
DYNAMIC EQ
Press
DYNAMIC EQ
Each time
the setting is changed as shown
below.
Dynamic EQ : ON
0dB (Film Ref) : This is the default setting and should be used when
Reference Level Offset
Audyssey Dynamic EQ is listening to movies.
referenced to the standard 5dB : Select this setting for content that has a very wide dynamic range,
film mix level. It makes such as classical music.
adjustments to maintain 10dB : Select this setting for jazz or other music that has a wider dynamic
the reference response range. This setting should also be selected for TV content as that is usually
and surround envelopment mixed at 10 dB below film reference.
when the volume is turned 15dB : Select this setting for pop/rock music or other program material
down from 0 dB. However, that is mixed at very high listening levels and has a compressed dynamic
film reference level is not range.
always used in music or
Setting is enabled when "Dynamic EQ" is "ON" (vpage 55).
other non-film content.
Dynamic EQ Reference
Level Offset provides three
offsets from the film level
reference (5 dB, 10 dB, and
15 dB) that can be selected
when the mix level of the
content is not within the
standard.
Confirm the setting
Audio/Video Adjust
Setting details
.
is pressed, the setting is changed as shown
Dynamic EQ : ON
Dynamic Volume : Evening
Dynamic EQ : ON Dynamic EQ : ON
Dynamic Volume : OFF Dynamic Volume : Day
.
is pressed,
Dynamic EQ : OFF
Return to previous menu
ENGLISH
55