Special Startup - Oki MC860 Maintenance Manual

Oki Data CONFIDENTIAL

5.12.2 Special startup

The special startups that are supported by MC860 are shown below.
Input code
100 Flash ROM forced initialization
Initializes all of the installed Flash ROM forcibly.
Forced initialization is possible only when the Service call 042 to 043 is issued.
101 Parameter forced initialization
Parameters are initialized forcibly in the case when the Service call 081 is
issued if EEP-ROM and Flash cannot be written or read normally, or if any core-
open parameter information is damaged.
102 Additional component ignore
MFP can be started up without loading the additional component by using the
DLM (Down Load Module) function even if additional component has been
stored in Flash ROM.
103 Download mode startup
MFP starts up in the download only mode of the additional component. At
present, additional component can be downloaded via Soft NIC only.
When the Soft NIC module is going to be newly added, the MFP should start up
in this mode.
104 Debug mode
Starts up the ROM debugger or the Target Shell.
105 ON LINE mode always
The errors that moves the MFP into the OFF LINE state are ignored, and the "ON
LINE mode always" condition is maintained.
106 FUSE KEEP MODE
This is the mode enabling operator to replace the consumable items with new
ones and checks the MFP operations while the power remains ON.
While an MFP is in the FUSE KEEP MODE, the new consumable item fuse will
not be cut, and the operation count is not added to the count value of old parts.
When the power of the MFP is turned OFF, MFP exits this mode. When the
power is turned ON next time, this mode becomes invalid.
110 Flash ROM initialization
The resident Flash ROM is initialized in the same way as in the case when the
following menus are selected: [Admin Setup] - [Management] – [Flash Memory
Setup] – [Initialize].
43967002TH Rev.1
Special mode
Input code
111 Language initialization
The downloaded message file is initialized in the same way as in the case when
the following menus are selected: [Admin Setup] - [Management] – [Language
Maint Setup] – [Initialize].
112 Setup value initialization
MFP is initialized in the same way as in the case when the following menus are
selected: [Admin Setup] - [Management] – [Reset Settings].
113 Erasure of individual personal information
Individual information that is registered in the MFP is erased in the same way
as in the case when the following menus are selected: [Admin Setup] -" [User
Install] - [Erasure Privacy Data].
114 HDD sector check
The HDD defective sector information is recovered and the HDD file system un-
match is recovered in the same way as in the case when the following menus
are selected: [Admin Setup] - [Management] – [Storage Maint Setup] - [Sector
check]. Management
115 HDD file system check
Resolves the un-match between the actual (free) space and displayed free
space of file system, and recovers the control data (FAT information) in the
same way as in the case when the following menus are selected: [Admin Setup]
- [Management] - [Storage Maint Setup] - [File system check].
120 Format HDD
HDD is initialized in the same way as in the case when the following menus
are selected: [System maintenance] – [Format HDD]. Contents of HDD are all
erased.
121 Format Flash ROM
Flash ROM is initialized in the same way as in the case when the following
menus are selected: [System maintenance] – [Format Flash ROM]. Contents of
the resident installed Flash device are all erased.
122 Administrator password reset
Administrator password is reset to default setup value in the same way as
in the case when the following menus are selected: [System Maintenance] –
[Change Password].
123 All Reset
Contents of the EEPROM, Flash ROM and HDD are returned to the default
values in the same way as in the case when the following menus are selected:
[System Maintenance] – [All Reset].
5. Maintenance Menu
Special mode
261 /