Table of Contents
Advertisement
B-3
GENERAL DESCRIPTION
The DC-600 is an SCR controlled three phase welding
and cutting power source. It uses a single range poten-
tiometer to control:
•
Submerged Arc Semi-Automatic or Automatic
Welding
•
Open Arc Semi-Automatic or Automatic Welding
•
Stick Welding
•
Air/Carbon Arc Cutting (Carbon Rod Sizes up to
3/8" Diameter)
The DC-600 has a three-position Welding Mode Switch
to enable the user to operate in one of three modes:
•
Constant Current (CC) Stick (also used for AAC)
•
Constant Voltage (CV) Submerged Arc
•
Constant Voltage (CV) Innershield (also used for
FCAW/GMAW)
Three models are available:
•
Domestic
-
all
60
230/460/575V.
•
Canadian-230/460/575V 60 Hertz models
•
Export-50/60 Hertz models
The optional Multi-Process Switch allows the user to
switch between semi-automatic or automatic welding
and stick welding or air/carbon arc cutting without dis-
connecting the wire feeder equipment control, elec-
trode,and work leads.
RECOMMENDED PROCESSES AND
EQUIPMENT
The DC-600 is designed for GMAW (MIG), FCAW, and
submerged arc (SAW) within the capacity of the
machine. It can also be used for stick welding (SMAW)
and for air carbon arc (AAC) cutting with carbon rods
up to 3/8" diameter.
The DC-600 is provided with a three position mode
switch that selects CV Innershield, CV Submerged Arc,
or CC Stick.
The DC-600 can be easily connected to wire feeding
equipment, including:
•
Semi-automatic wire feeders LN-7, LN-7 GMA, LN-
742, LN-8, LN-9, LN-9 GMA, LN- 10, LN-15 LN-
23P, LN-25, and DH-10.
•
Automatic wire feeders NA-3, NA-5, and NA-5R.
•
Tractors LT-56 and LT-7
OPERATION
Hertz
models
except
DC-600
DESIGN FEATURES AND
ADVANTAGES
•
Excellent arc characteristics for optimum constant
voltage submerged arc and Innershield welding
performance.
•
A control circuit designed to provide good starting
for a large variety of processes and procedures.
•
Output Control Potentiometer that provides easy
single range continuous control.
•
Output Control Switch that provides simple switch-
ing from local to remote control.
•
Output Terminals Switch to energize output termi-
nals either local or remote.
•
White neon pilot light to confirm that the Input
Contactor is energized.
•
DC Ammeter and Voltmeter
•
42VAC 10 Amp auxiliary power available for the
wire feeder, circuit breaker protected.
•
Single MS-type (14 pin) connector for wire feeder.
•
115VAC 15 Amp auxiliary power available for the
wire feeder, circuit breaker protected.
•
115VAC 15 Amp duplex plug receptacle available
on 60 Hertz models, circuit breaker protected.
•
Multi-functional terminal strip for easy connection
of wire feeding control cables.
•
Recessed output terminals to avoid any person or
object from accidentally coming into contact with
the output terminals and labeled " + " and " - " for
easy identification.
•
Thermostatically protected power source.
•
Electronic protection circuit to protect power
source against overloads.
•
Input line voltage compensation to provide an
essentially constant output.
•
SCR electronically controlled welder output pro-
vides extra long life, especially for highly repetitive
welding applications.
•
Solid state 2 and 4 circuit for extra long life.
•
Two circuit solid state control system provides
maximum performance and circuit protection.
•
Low profile case provides maximum use of space.
•
Convenient access to all controls.
•
Output lead strain relief loops to prevent terminal
and cable damage.
•
Easily removed case side, even when stacked.
•
Outdoor operation because enclosure is designed
with air intake louvers that keep dripping water
from entering the unit. Transformer, SCR bridge,
and choke have special corrosion resistant paint
for added protection.
B-3
Advertisement
Chapters
Table of Contents
Troubleshooting
