Table of Contents
Advertisement
RANGER AIR
260MPX
®
TECHNICAL SPECIFICATIONS -
RANGER AIR 260MPX (KOHLER) (K5238-1)
WELDING PROCESS
DC Stick Welding
Ranger Air 260MPX
(constant current)
Touch-Start TIG
Ranger Air 260MPX
DC MIG/FCAW Welding
Ranger Air 260MPX
(Constant Voltage)
AUXILIARY OUTPUT @ 104 °F (40°C)
MODEL
CONTINUOUS PEAK RECEPTACLE CIRCUIT
Single
Ranger
Phase
9,000 Watts
Air
60Hz
260MPX
Lift bail rating 1085 lb (492 kg) Maximum.
ENGINE SPECIFICATIONS
Make/Model
Kohler electronic throttle body
-ECH749 (26.5 hp)
EPA Emission
Evaporative
Displacement
45 cu. in. (747 cc)
Speed
3600 rpm @ full load
2500 rpm @ low idle
Warranty (USA)
2 year complete (parts and labor)
3 year major components (parts and
labor)
12VDC Battery LB1
Battery
BCI group size 99 or 99R
410 cold cranking amps
Fuel System
Electric lift pump, fuel injected
Air Cleaner
Dual Element
Engine Protection Low Oil Pressure
Capacities
Fuel: 11 gal (41.6 L)
Oil: 1.9 qts (1.8 L)
IEC 60974-1; IP23S
-10°C TO +40°C OPERATING RANGE.
WELDING RATED OUTPUT @ 104°F (40°C)
MODEL
WELDING OUTPUT - IEC RATING
Current/Voltage/Duty Cycle
35A / 21.4V / 100 % - 231A / 29.2V / 100 %
25A / 11V / 100 % - 255A / 20.2V / 100 %
35A / 15.8V / 100 % - 253A / 26.7V / 100 %
BREAKER
120 VAC
20 Amps
Duplex (5-20R)
GFCI Protected
120/240 VAC
50 Amps
11,500
Dual Voltage
Watts
Full KVA
(14-50R)
240 VAC
50 Amps
(6-50R)
OTHER RATINGS
260A / 26V / 100 % 80 Volts
260A / 26V / 100 %
260A / 26V / 100 %
AIR COMPRESSOR SPECIFICATIONS
Compressor
Single stage, oil injected
Type
rotary screw
Air compressor
40 CFM @ 150 psi
capacity
Inlet Control
Zero (0) no load / 100% load; proportional type
Pleated paper, dry type
70 micron spin-on type
Oil capacity
3 quarts, genuine Vanair Oil
Safety relief
225psi
valve setting
Electrical system
12 VDC
Cooling system
Air to oil heat exchanger
Air service
Three #8 SAE/ORB
outlets
BATTERY CHARGE
MODE
OUTPUT
Charging
50 Amps
Jump Assist
260 Amps
GENERAL DESCRIPTION
The Ranger Air 260MPX is a compact, versatile machine ideally
®
suited for service trucks.
The small size allows more room for trucks to carry tools and
other equipment, while the low weight allows for easily meeting
DOT requirements and ability to haul additional equipment
without overloading the chassis.
Low sound improves work place safety and may qualify the
machine for low noise regions, such as near schools or hospitals.
Reduced fuel consumption is achieved through advanced engine
start/stop controls and variable engine speed during idling,
welding or using the compressor.
The rotary screw air compressor supplies powerful instant air for
common tools.
The machine's battery jump and charge capability provides
power for 12V and 24V batteries.
A-1
INSTALLATION
MAXIMUM WELD OCV
@ RATED LOAD RPM
30 Volts
80 Volts
BATTERY VOLTAGES
12V
24V
Advertisement
Table of Contents
