Error Messages - Yamaha RX-V571 Owner's Manual

1 2 3 4 5 6 7 8
Optimizing the speaker settings automatically (YPAO)

Error messages

If any error message is displayed during the measurement, resolve the problem and perform YPAO again. Error message can be confirmed and controlled by viewing both a TV
monitor and the front display.
TV monitor
■
Cause and remedy for each error message
Error message Cause
E-1:No Front SP Front speakers are not
(E-1:NO FRNT SP) detected.
E-2:No Sur. SP Either of surround
(E-2:NO SUR SP) speakers is not detected.
A surround back speaker
E-4:SBR→SBL
is connected to the R side
(E-4:SBR->SBL)
only.
E-5:Noisy
The noise is too loud.
(E-5:NOISY)
Any surround back
E-6:Check Sur. speaker is connected
(E-6:CHECK SUR) while no surround
speakers are connected.
E-7:No MIC The YPAO microphone has
(E-7:NO MIC) been removed.
The YPAO microphone
E-8:No Signal
(E-8:NO SIGNAL) cannot detect test tones.
E-9:User Cancel The measurement has
(E-9:CANCEL) been canceled.
E-10:Internal Err. An internal error has
(E-10:INTERNAL) occurred.
YPAO
VOL. VOL.
ENHANCER iPod CHARGE SLEEP
STEREO
TUNED
SW SW
PL
E-1:NO FRNT SP
C C
L L
SL SL
Front display
Follow "Procedure to exit YPAO" to exit YPAO, turn off the unit, and then check the speaker connections. After removing problems, turn on the unit, and
then perform YPAO again.
When using only one surround back speaker, you need to connect it to the SINGLE jack (L side). Follow "Procedure to exit YPAO" to exit YPAO, turn off the
unit, and then reconnect the speaker. After reconnecting, turn on the unit, and then perform YPAO again.
Keep the room quiet and select "RETRY (Retry)" in step 2 of "Procedure to exit YPAO" to restart YPAO for an accurate measurement. Selecting
"PROCEED (Proceed)" allows you to continue measuring, but may not achieve the optimal results.
We recommend selecting "RETRY (Retry)" or "EXIT (Exit)" to retry YPAO again from the beginning.
Surround speakers should be connected when using surround back speakers. Follow "Procedure to exit YPAO" to exit YPAO, turn off the unit, and then
reconnect the speakers. After reconnecting, turn on the unit, and then perform the YPAO measurement again.
Connect the YPAO microphone to the YPAO MIC jack firmly and select "RETRY (Retry)" in step 2 of "Procedure to exit YPAO" to restart the measurement.
Connect the YPAO microphone to the YPAO MIC jack firmly and select "RETRY (Retry)" in step 2 of "Procedure to exit YPAO" to restart the measurement.
If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or service center.
Select "PROCEED (Proceed)" in step 2 of "Procedure to exit YPAO" to resume the measurement. Select "RETRY (Retry)" to restart the measurement from
first.
Follow "Procedure to exit YPAO" to exit YPAO, turn off and on the unit. Perform YPAO again. If this error occurs repeatedly, contact the nearest authorized
Yamaha dealer or service center.
■
Procedure to exit YPAO
1
Check the contents of error message, and then press ENTER.
2
Press the cursor key ( ) to select "EXIT (Exit)" from the following
choices, and then press ENTER.
Choices: PROCEED (Proceed) (E-5, E-9 only), "RETRY (Retry)," "EXIT (Exit)"
3
PR
Press the cursor key ( ) to select "Exit (Exit)" from the following
R R
SR SR
choices, and then press ENTER.
Choices: Start (Start), Exit (Exit)
4
Remove the YPAO microphone.
Remedy
32
En