Table of Contents
Advertisement
Display
No
Character code
INVALID TC
96
SEQUENCE
97
NO ACTIVE FRAME
INVALID FRAME
98
RATE
*
7
An attempt to start recording causes the button to temporarily light. It goes out a few seconds later and no recording is made.
The following warning messages appear when an incorrect operation is attempted in the thumbnail playlist screen.
Item
Message
CANNOT ACCESS
GATEWAY!
CHECK LAN SETTING
CANNOT ACCESS!
CANNOT ADD! NO
INPUT
CANNOT CHANGE!
CANNOT CONNECT! Connection to the network cannot be established. Check LAN setup, make sure the LAN cable is
CANNOT CONVERT! Inconvertible clips are included.
CANNOT DELETE!
Thumbnail
CANNOT FIND
FTP-SERVER!
CANNOT FORMAT!
CANNOT
RE-CONNECT!
CANNOT REPAIR IN
SELECTION!
CANNOT REPAIR!
CANNOT SAVE!
FILE NAME IN USE
CARD FULL!
INVALID VALUE!
IP ADDRESS IS
USED!
LACK OF REC
CAPACITY!
Appears during playback when frame rate data in user bit cannot be detected or when
the playback time code is not continuous. The video output is distorted and audio output
is muted in sections where the time code is not continuous. Check the playback clip.
Appears during EE or recording when frame rate data cannot be detected in the user bit
data in an HD SDI input or when the input time code is not continuous. Normal recording
will not be possible under these conditions. Check signal input to the unit. Input signals
with a matching time code and pull-down sequence (Appears when 23.98, 24, 59-23, 60-
24 or 60-25 is set in setup menu No. 25 (SYSTEM FREQ).)
Appears when active frame data cannot be detected in the user bits in the HD SDI input
during EE or recording. Normal recording will not be possible under these conditions.
Check signal input to the unit. The input signal must contain the active frame data from a
variable frame-rate camera. (Appears when 29.97, 59-23, 60-24 or 60-25 is set in setup
menu No. 25 (SYSTEM FREQ) and setup menu No 040 (VFR REC) is set to ON.)
Appears when active frame data detected from the user bit in the HD SDI input during EE
and recording exceeds 50p. Normal recording is not possible under these conditions.
When SYSTEM FREQ is set to 60-25, set the frame rate on a variable frame-rate camera
to 50p or less. Appears when SYSTEM FREQ is set to 60-25 and VFR REC is set to ON.
Description
Cannot access gateway server.
Data cannot be accessed because it is corrupted
or for other reasons.
User name or password in not entered correctly. Enter user name or password correctly.
A thumbnail containing a grayed out text memo that
cannot be generated is not available for editing.
Contents version mismatch prevents deletion.
FTP server cannot be found.
P2 card problem prevents formatting.
A clip that does not span multiple cannot be
reconnected.
Some of the selected clip could not be repaired.
Selected content cannot be repaired.
A network setup file with the same file name
exists on the SD memory card.
The P2 or SD memory card is full.
Entered data was invalid.
The set IP address is used on another device.
There is not enough recording capacity left on the
card.
Description
Check if LAN setup is correct.
Restore media and clips to normal state before
access. When displayed during network operation,
check LAN setup, make sure the LAN cable is
correctly connected and check that your network
environment is functioning properly.
Edit settings or content to enable thumbnail display.
correctly connected and check that your network
environment is functioning properly.
Check the selected content.
Match devices and contents version.
Check if FTP client URL is correct.
Check P2 card.
Check selected content.
Check selected content.
Save to a different name.
Insert media with sufficient capacity.
Enter data in a valid range.
Consult the network administrator, and set another
IP address.
Insert a card with sufficient recording capacity.
For Long and Trouble-Free Operation: Error Messages
Deck operation
Operation
continues
Recording is
*
7
disabled
Operation
continues during
recording
Operation
continues
Measure
211
Advertisement
Table of Contents
