Table of Contents
Advertisement
6
Repeat steps 3 to 5, and adjust each band level.
.Frequency Adjustment (Fo)
Band1 (63 Hz) / Band2 (150 Hz) / Band3 (400 Hz) /
Band4 (1 kHz) / BandS (2.5 kHz) / Band6 (6.3 kHz) /
Band? (17.5 kHz)
.Level Adjustment (Gain)
Adjustable output level: -6 to +6 dB
• During adjuslment, ((you press in Ihe otl1er ring and mIMe Ihe
Double Action encoder to the leli or right, Ihe band changes, and
you can adjusllhe adjacent band. ((you pre.H then mlllte and hold
the Double Action encoder to the leli or right, the band continuously
changes.
• Thejimction is inoperable when Defeal is set to ON.
Adjusting the Crossover Settings
Sound Field Adjustment
~
X-Over
Before performing the following procedures. refer to "About the
Crossover" (page 3S).
1
Rotate the Double Action encoder to select
"X-Over" in the Sound Field adjustment mode, and
then press ~ fENTER.
2
Rotate the Double Action encoder to select the
band, and then press ~fENTER.
If a band is selected, each band screen to be adjusted is
displayed .
Adjusting the Time Correction
Sound Field Adjustment
~
Time
Correction
Before performing the following procedures. refer to "About Time
Correction" (page 34).
1
Rotate the Double Action encoder to select "Time
Correction" in the Sound Field adjustment mode,
and then press ~fENTER.
Depending on the X-OVER switch setting on the IMPRINT
audio processor (PXA-H 100), the speaker to be adjusted
differs.
3WAY System / Normal (L=R)
Setting items:
Low/Mid-Low/Mid-High/High
3WAY System /Individual (LIR)
Setting items:
Low ULow R/Mid-Low UMid-Low R/Mid-High U
Mid-High R/High UHigh R
F/R/SUBW. System / Normal (L=R)
Setting items:
Subw./Rear/Front
3WAY System
High LI High R / Mid LI Mid R /Low LI Low R
FIR/SUBW. System /Individual (UR)
Setting items:
Subw. USubw. R/Rear URear R/Front UFront R
FIR/SUBW. System
Front LI Front R / Rear LI Rear R / Subw. LI Subw. R
2
Rotate the Double Action encoder to select the
speaker, and press
~fENTER.
• Depending on the current syslem, s'electable band content dilj'ers.
Refer
10
"Setting Ihe Filler type" (page
3/)
and the setting of Ihe
X-OVER switch on the IMPRINT audio processor (PXA-HIOO).
3
Rotate the Double Action encoder to adjust the
frequency/slope/level.
The currently adjusted item lights up.
If
Time
Correction
4
The adjustment content is selected by pressing
~fENTER,
and operation shifts to a next
adjustment item.
5
When the selected band settings are complete,
press BAND.
The next band adjustment screen is displayed.
6
Set all bands by repeating steps 3 to 5.
Cut-off
frequency
Front L
~
~
000
000
000
~
~
000
000
~
~
;00
SP Fr"1l1 L
Adjust
00 Oem
Rotate the Double Action encoder to set to the
distance of each speaker.
00 cm-336.6 cm (0.0 inch-132.7 inch)
Selected
speakers - -
4
If
~fENTER
is pressed, the adjustment value is
set, and the speaker selection mode is activated.
5
Repeat steps 2 to 4, and set the all speakers.
3
• During adjuslmelll, ((you press in the outer ring and millIe Ihe
Double Action encoder to Ihe leji or right, the speaker changes, and
you can adjust the adjacent speake/: I(you press Ihen mlate and hold
the Double Action encoder
10
Ihe leli or right, Ihe speaker
continuously changes.
You ClIn also change Ihe speaker by pressing BAND.
32-EN
Advertisement
Table of Contents
