DSC PowerSeries PC1616 Installation Manual page 20

PowerSeries - PC1616/PC1832/PC1864
Section [170] PGM Output Timer
Program the time, in seconds, PGM outputs programmed to follow the PGM Output Timer will activate for. Valid entries are [001] to [255].
Section [171] Tamper PGM Output Timer
Program the time, in minutes, that a tamper condition will latch the Tamper PGM output. Valid entries are [000] to [255].
Section [175] Auto-arm Postpone Timer
Program the time, in minutes, that the system will postpone automatic arming. After the programmed time, the system will attempt to auto
arm again. If data [000] is programmed, the system will instead abort the auto arm sequence. Valid entries are [001] to [255].
Section [176] Cross Zone/Police Code Timer
Program the time, in seconds (Cross Zone) or minutes (Police Code), that the panel will use to determine if a Cross Zone or Police Code
event has occurred. If data [000] is programmed when using the Police Code feature, the panel will generate a Police Code event if any two
zones go into alarm during any armed-to-armed period. Valid entries are [001] to [255].
Section [181] to [188] Auto-arm Schedules
Program the time to auto arm (section [181] for partition 1, Section [182] for partition 2 etc.) for each day of the week. Each section has
seven, 4-digit entries, two digits for the hour, two digits for the minute, for Sunday through Saturday. Program using the military format (for
example, to auto arm at 8:00 pm program data [20][00]). Valid entries are [00][00] to [23][59] – program [99][99] to disable auto arming.
Section [190] No Activity Arming Pre-alert Duration
Program the time, in minutes, for the No Activity Arming Pre-Alert Duration. The keypads will provide a steady tone warning the user that
the system will arm. The user can either violate a zone or press any key to abort the arming sequence. Valid entries are [000] to [255].
Section [191] to [198] No Activity Arm Timer
Program the time, in minutes, for the No Activity Arm Timer (Section [191] for Partition 1, Section [192] for Partition 2 etc.). If Delay Zones
are restored and no zone activity is detected for the time programmed, the system will start the auto arm sequence. Valid entries are [000] to
[255].
Section [199] Auto-Arming Pre-alert Timer
Program the time, in minutes, for the Auto-Arming Pre-Alert Time. This timer is used for all programmed auto-arming features (is not used
for No Activity Arming). The keypads will provide a steady tone warning the user that the system will arm. The user can enter a valid access
code to abort the arming sequence. Valid entries are [001] to [255].
Section [201] Partition Selection Mask
Turn the corresponding option ON to enable partitions [1] to [8]. ON (bit 1 cannot be turned OFF).
Section [202] to [265] Partition Zone Assignments
These Sections are used to assign zones to specific partitions (Section [202] to [209] for Partition 1, Sections [210] to [217] for Partition 2
etc.). Turn ON the option corresponding to the partition and zone to enable the zone on the specified partition. Turn the option OFF to dis-
able the zone on the specified partition. Zones assigned to more than one partition are called 'common zones' and will only be armed if all
the partitions the zone is assigned to are armed. Default = Zones 1-8 enabled on Partition 1.
Section [301] to [303] Telephone Numbers
Program the phone numbers as required. Phone Number 3 is dedicated as a back-up to Phone Number 1. HEX digits can be included for spe-
cial applications:
HEX [A]
HEX [B]
HEX [C]
HEX [D]
HEX [E]
HEX [F]
Section [304] Call Waiting Cancel String
Program the digits required to disable call waiting. If enabled, the system will dial the programmed string on the first dialing attempt.
Program unused digits with data [F].
Section [310] System Account Number
Program the System Account Number. Only the SIA format supports 6-digit account numbers. If a 4-digit account number is required,
program the last two digits as data [FF]. If using the SIA format, this account number will be used for all reporting events. If using a
18
Not used
Simulates a [ ] key press
Simulates a [#] key press
Additional dial tone search
2-second pause
End of phone number marker
WWW.DIYALARMFORUM.COM