Sign in today to find solutions:

Don't have an account? Sign up

 
WARNING:
This manual contains information on limitations regarding product use and function and
information on the limitations as to liability of the manufacturer. The entire manual should be carefully read.
PC1616/PC1832/PC1864
User Manual
Next page ->

Summary of Contents

  • Page 1

    WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. PC1616/PC1832/PC1864 User Manual...

  • Page 2: Table Of Contents

    Table of Contents PowerSeries System Keypads ............1 Keypad Display Symbols .

  • Page 3: Table Of Contents

    User Function Commands ............. . 13 Changing Brightness/Contrast .

  • Page 4

    This equipment gener- DSC c/o APL Logistics 757 Douglas Hill Rd, Lithia Springs, GA 30122 ates, uses and can radiate radio frequency energy and, if not installed and used in accordance Additional Information with the instructions, may cause harmful interference to radio communications.

  • Page 5: Powerseries System Keypads

    PowerSeries System Keypads PC5532Z Zone Function Lights Lights PC5508Z Status Lights PC5516Z Function Buttons Emergency Keys Your installer may have installed one of these LED keypads if you have 16 or fewer zones on your sys- tem. These keypads operate in the same way as the PC5532 keypad.

  • Page 6

    PK5500/PK5501 PC1555RKZ Status Lights PK5508/PK5516 (shown) Number Zone Lights Stay Away Chime Reset Emergency Bypass Keys LED5511 LCD5511 Display System Lights Number...

  • Page 7: Keypad Display Symbols

    Keypad Display Symbols LCD5501 Fixed Message LCD5501 ICON PK5501 PK5508/PK5516 LCD5511 LED5511 Clock Digits 1, 2 – These two 7 segment clock digits indicate the hour digits when the local clock is active, and identify the zone when the OPEN or ALARM icons are active. These two digits scroll one zone per second from the lowest zone number to the highest when scrolling through zones.

  • Page 8: Access Codes, System Information

    Reference Sheets Fill out the following information for future reference and store this guide in a safe place. Access Codes Master Code [40] : _________________________ Code Access Code Code Access Code Code Access Code Code Access Code 33 (Duress) 34 (Duress) System Information Enabled? FIRE...

  • Page 9: Sensor / Zone Information

    Sensor / Zone Information Sensor Protected Area Sensor Type Sensor Protected Area Sensor Type...

  • Page 10: About Your Security System, Fire Detection, Testing, Monitoring, Maintenance, General System Operation

    General System Operation Your security system is made up of a DSC control panel, one or more keypads and various sensors and detectors. The control panel will be mounted out of the way in a utility closet or in a basement. The metal cabinet contains the system electronics, fuses and standby battery.

  • Page 11: Pk5500 Language Selection, Arming (turning On/setting), Away Arming (turned On/set), Quick Exit

    Additional features of the PC1616/PC1832/PC1864 Security System are an Automatic Inhibit (Swinger Shutdown) for Alarm, Tamper and Trouble signals after 3 occurrences in a given set period (see Section 5.6 Option [377] in the Installation Manual). There is also a Programmable Keypad Lockout option (see Section 5.3 Option [012] in the Installation Manual).

  • Page 12: Disarming (turning Off /unsetting), Stay Arming (partially Turning On / Part Setting), Night Arming

    Remote Arming and Disarming The system can be armed and/or disarmed using the remote control device (wireless key) model DSC WS4939. When arming the system by using the Arm button on the wireless key, the system will acknowledge the command by sounding a single bell squawk and when disarming using the Disarm button on the wireless key the system will acknowledge the command by sounding two bell squawks that can be heard from the exterior of the premises.

  • Page 13: When Alarm Sounds, Intrusion (burglar) Alarm Continuous Siren, Fire Alarm Pulsed Siren, Bypassing Zones

    When Alarm Sounds The system can generate 2 different alarm sounds: Continuous Siren = Intrusion (Burglary Alarm) Temporal / Pulsed Siren = Fire Alarm Intrusion (Burglar) Alarm Continuous Siren If you are unsure of the source of the alarm approach with caution ! If the alarm was accidental, enter your Access Code to silence the alarm.

  • Page 14

    4. To unbypass a zone, enter the two-digit number of the zone(s) to be bypassed (01-64). You can also use the keys to find the zone, and then press to select the zone. The “B” will disappear from the dis- play to show that the zone is no longer bypassed.

  • Page 15: Trouble Conditions, Trouble Menu Acknowledgement, Alarm Memory, Door Chime (entry/exit Beeps), Access Code Programming

    Trouble Conditions When a trouble condition is detected, the Trouble ( ) or System indicator will turn on, and the keypad will beep every 10 seconds. Press the key to silence the beeps. Press to view the trouble condition. The Trouble ( ) or System indicator will flash.

  • Page 16: User Code Attributes, Access Codes

    For systems using multiple partitions/areas, access codes can be assigned to specific or multiple partitions/areas. Please contact your alarm company for details. The minimum number of variations of access codes (key) is 27027 when 37, 6-digit user codes are used. For SIA Installations, duplicate or duress codes derived from user codes +/- 1 digit are not allowed.

  • Page 17: Bell Squawk Attribute, Partition Assignment Mask, Erasing An Access Code, User Function Commands

    Bell Squawk Attribute This attribute is used to determine whether an access code should generate an arming/disarming Bell Squawk upon entry of the code for Away arming. The Wireless Keys with access codes associated with them may gener- ate Arming/Disarming Bell squawks. If desired, this option may be used with codes that are manually entered. Please contact your installer to have this programmed.

  • Page 18

    [2] Auto-arm Control Pressing [2] while in the User Function menu will enable (3 beeps) or disable (one long beep) the Auto-arm fea- ture, by partition. With this feature enabled, the panel will automatically arm in the Away mode (Stay Away zones active) at the same time each day.

  • Page 19: Changing Brightness/contrast, Changing The Buzzer Level, Label Programming

    Changing Brightness/Contrast PK5500/LCD5500 keypads When this option is selected, the keypad will allow you to scroll through 10 different brightness/contrast levels. 1. Press [Master code]. 2. Use the keys to scroll to either Brightness Control or Contrast Control. 3. Press to select the setting you want to adjust.

  • Page 20: Viewing The Event Buffer From A Pk5500/lcd5500 Keypad, Pk5500 Global Status Screen, Sensor Reset

    Refer to the following chart: [1] - A, B, C, 1 [6] - P, Q, R, 6 [2] - D, E, F, 2 [7] - S, T, U, 7 [3] - G, H, I, 3 [8] - V, W, X, 8 [4] - J, K, L, 4 [9] - Y, Z, 9,0 [5] - M, N, O, 5...

  • Page 21: Testing Your System, Testing Your Keypad Sounder And Siren, Testing Your Entire System

    Testing Your System NOTE: If you are going to perform a System Test, call your Monitoring Station to inform them when you begin and also when you end the test. Testing Your Keypad Sounder and Siren The System Test provides several system tests, and a two-second check of the keypad sounder and bell or siren. 1.

  • Page 22: Guidelines For Locating Smoke Detectors

    Guidelines for Locating Smoke Detectors Research has shown that all hostile fires in homes generate smoke to a greater or lesser extent. Experiments with typical fires in homes indicate that detectable quantities of smoke precede detectable levels of heat in most cases. For these reasons, smoke alarms should be installed outside of each sleeping area and on each storey of the home.

  • Page 23: Household Fire Safety Audit, Fire Escape Planning

    Household Fire Safety Audit Read this section carefully for important information about fire safety. Most fires occur in the home. To minimize this danger, we recommend that a household fire safety audit be con- ducted and a fire escape plan be developed. 1.

  • Page 24: New Zealand Telecom Network

    New Zealand Telecom Network The following is a list of warnings applicable when this equipment is connected to the New Zealand Telecom Network : General Warning The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network.

  • Page 25

    DSC. Custom products are only warranted to the extent that they do not func- contract, negligence, strict liability, or any other legal theory. Such damages tion upon delivery.

  • Page 26

    Notes...

  • Page 28

    ©2006 Digital Security Controls Toronto, Canada • www.dsc.com 2 9 0 0 7 1 6 5 R0 0 2 Printed in Canada...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: