Bosch D9412GV2 Operation And Installation Manual page 6

Figures
Figure 1: System Configuration..............................9
Figure 2: Enclosure Mounting ..............................15
Figure 3: Ground Fault Detection.........................16
Figure 4: Ground Fault Detect (S4)......................17
Figure 5: Area 5 Silent Alarm Relay in RPS.........17
Figure 6: Reset Pin...............................................18
Figure 7: D9412GV2 Service Walk Test Flow
Chart .....................................................21
Figure 8: D7412GV2 Service Walk Test Flow
Chart .....................................................22
Figure 9: Non-Power-Limited Wiring ....................25
Figure 10: Charging and Battery LEDs ..................26
Figure 11: RJ31X Wiring ........................................30
Figure 12: Phone Connector, Phone LED, and
Operation Monitor LED Locations.........30
Figure 13: D928 Dual Phone Line Switcher...........33
Figure 14: On-board Point Sensor Loop Wiring.....35
Figure 15: Rothenbuhler 5110/4001-42 High
Security Bell Wiring Configuration ........37
Figure 16: Wiring the Rothenbuhler 5110/4001-42
High Security Bell to the D9412GV2
or D7412GV2 Control Panel .................38
Figure 17: Connecting the D8125 POPEX to the
D9412GV2 Control Panel .....................41
Figure 18: Connecting the D8125 POPEX to the
D7412GV2 Control Panel .....................42
Figure 19: Program Record Sheet .........................45
Figure 20: D8128D OctoPOPIT Layout..................46
Figure 21: Connecting D8128D OctoPOPITs to
the D9412GV2 ......................................49
Figure 22: Connecting D8128D OctoPOPITs to
the D7412GV2 ......................................50
Figure 23: Wiring Multiple D8128Ds Using
®
Molex Connectors ...............................51
Figure 24: D8128D OctoPOPIT Sensor Loops ......52
Figure 25: D8129 Connections to the D9412GV2 .53
Figure 26: D8129 Connections to the D7412GV2 .54
Figure 27: D811 Module Wiring to the
D9412GV2 ............................................56
Figure 28: D811 Module Wiring to the
D7412GV2 ............................................57
Figure 29: Power at Keypads.................................60
Figure 30: Keyswitch Wiring...................................61
Figure 31: D9133 Jumper Setting for Address 80..64
Figure 32: DX4010i DIP Switch Settings................64
Figure 33: DX4020 DIP Switch Settings ................65
Figure 34: Reset Pin...............................................66
6
D9412GV2/D7412GV2 | Operation and Installation Guide | Contents
Figure 35: Programmer and Accessory
Figure 36: D9412GV2 Faceplate........................... 67
Figure 37: D7412GV2 Faceplate........................... 68
Figure 38: D9412GV2, Power Supply Side ........... 69
Figure 39: D9412GV2, Input Points and
Figure 40: D9412GV2, SDI Devices...................... 71
Figure 41: D7412GV2, Power Supply Side ........... 72
Figure 42: D7412GV2, Input Points and
Figure 43: D7412GV2, SDI Devices...................... 74
Table 1:
Table 2:
Table 3:
Table 4:
Table 5:
Table 6:
Table 7:
Table 8:
Table 9:
Table 10:
Table 11:
Table 12:
Table 13:
Table 14:
Table 15:
Table 16:
Table 17:
Table 18:
Table 19:
Table 20:
Table 21:
Table 22:
Table 23:
Table 24:
Table 25:
Table 26:
Table 27:
Connections.......................................... 66
Peripheral Devices ............................... 70
Peripheral Devices ............................... 73
Tables
Related Documentation.......................... 7
GV2 Series Control Panel Differences ... 9
Compatible Accessories....................... 10
Software Version Compatibility of
D6500 MPU and Line Cards ................ 13
Compatible Keypads and Command
Centers ................................................. 13
Ground Fault Impedance
Specifications ....................................... 17
Battery Discharge and Recharge
Schedule............................................... 27
Charging Status and Low Battery
LEDs..................................................... 27
Phone Cord Lengths............................. 33
Point Parameters.................................. 35
POPEX Modules................................... 39
Extra Point Events ................................ 39
Off-Board Point Errors .......................... 40
Data Expansion Loop Wire
Specifications ....................................... 43
D8128D OctoPOPIT Switch Settings
for D9412GV2 and D7412GV2............. 47
Switch 5 Settings for Line Termination. 47
Terminal Strip Connections .................. 48
D8129 OctoRelay Switch Settings ....... 54
Number of D8128Ds Used with D8129s
.............................................................. 55
Keypad Address Settings ..................... 58
Keypad Connections ............................ 59
SDI Device Connections ...................... 62
Printer Address Switch Settings ........... 62
Address Switch Settings for Access
Control Module ..................................... 63
Zonex 1 Point Address Chart ............... 75
Zonex 2 Point Address Chart ............... 76
Specifications ....................................... 77
Bosch Security Systems, Inc. | 7/09 | F01U003641-04