Setting The Clock - Sharp XL-HP700 Operation Manual

XL-HP700
Setting the clock
/ 1 ' \
'\ l /
1'-1'-.'-11-/.....
/ C:J... : U U,-
C".'""".".,.,.""",.""L .•. " .' , ."""." • . • . , .,.""",.' " . . • •. . ,.".0"""".', . . " """,' : .,.,."."".' " ,' " ," . . . "".'",C"".: •. ,.""."",:.,' " ,' , ."' " ,"' . • '",'.","'.'.",K.",.",.,,,
II
0 0 0
II
.-r~D
'-I
'III r-,
I /
'-/'1/1
r-/ / /
/ 1'\
'\ 1 /
. . . . . . /'-/--:/-/ '-I
-:' Uj:.1 U
'-I
/11/
r-, , /
'\ 1 /
' - --_/-_-=1_/' _ 11_ _
I......;;.C--"'{--;-:~----'I,L"'7-~=-
¢
5
Press the TUNINGITIME (V or A) button to adjust the min-
utes and then press the MEMORY/SET button.
4
Press the TUNINGITIME (V or A) button to adjust the hour
and then press the MEMORY/SET button.
• Press the TUNINGITIME (V or A) button once to advance
the time by 1 minute. Hold it down to change the time in 5-
minute intervals.
• The hour will not advance even if minutes advance from "59"
to "00".
• Press the TUNING/TIME (V or A) button once to advance
the time by 1 hour. Hold it down to advance continuously.
• When the 12-hour display is selected, "AM" will change au-
tomatically to "PM".
To confirm the time display:
Press the CLOCK button on the main
unit or remote control.
The time display will appear for about 5
seconds.
Note:
The "CLOCK" or time will flash at the push of the CLOCK button
when the AC power supply is restored after a power failure or
unplugging the unit.
Readjust the clock as follows.
To readjust the clock:
Perform "Setting the clock" from step 1. If the "CLOCK" is not flash-
ing in step 2, step 3 (for selecting the 12-hour or 24-hour display)
will be skipped.
To change the 12-hour or 24-hour display:
1 Clear all the programmed contents. [Refer to "Clearing all the
memory (resetr' on page 29 for details.]
2 Perform "Setting the clock" from step 1.
) 1 ' \
'\ 1 /
' / -/--:,-/ '-I
-:1
C.J"_'
U
'-I
/11/ r-, ,
1
CLOCK
(I)(Q)
TUNING/TIME
'v' /'..
(Q)(I)
I ! I I
\ I I I I
'-,-, '-I ,- ,
1./
- '- '- '-' ,_ r, -
I ! I I \
"AM 12:00"
~
The 12-hour display will appear.
(AM 12:00 - PM 11 :59)
"AM 0:00" ~ The 12-hour display will appear.
(AM 0:00 - PM 11 :59)
"0:00" ~ The 24-hour display will appear.
(0:00 - 23:59)
Note that this can only be set when the unit is first installed or it
has been reset. [Refer to "Clearing all the memory (reset)" on
page 29 for details.]
\ I I I
I -
/FI
/' 1 1
2
Press the CLOCK button on the main unit and, within 5 sec-
onds, press the MEMORY/SET button.
3
Press the TUNINGITIME (V or A) button to select 12-hour
or 24-hour display and then press the MEMORY/SET but-
ton.
The clock should be set on the main unit.
In this example, the clock is set for the 12-hour (AM 12:00) display.
1
Press the ON/STAND-BY button to turn the power on.
14