Setting The Speakers For A Surround Field - JVC RX-9010VBK Instructions Manual

Setting the Speakers for a Surround
Field
To obtain the best possible surround sound of the Surround and DSP
modes, you have to register the information about the speakers
arrangement after all connections are completed.
• This function is applied only to the main room sources.
Before you start, remember....
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
Front, Center, and Rear Speaker Setting
Register the sizes of all the connected speakers.
• When you change your speakers, you need to register the
information about the speakers again.
On the front panel ONLY:
1. Press SETTING repeatedly until
"FRONT SPK" (Front Speaker),
"CTR SPK" (Center Speaker) or
"REAR SPK" (Rear Speaker)
appears on the display.
The display changes to show the current setting.
2. Press CONTROL UP 5 /DOWN ∞
to select the appropriate item
about the speaker selected in the
above step.
• Each time you press the button, the
display changes to show the following:
LARGE SMALL
LARGE: Select this when the speaker size is relatively large.
SMALL: Select this when the speaker size is relatively small.
NONE: Select this when you have not connected a speaker.
(Not selectable for the front speakers)
3. Repeat steps 1 and 2 to select the appropriate
items for the other speakers.
Notes:
• Keep the following comment in mind as reference when adjusting.
– If the size of the cone speaker unit built in your speaker is greater
3
than 4 / inches (12 cm), select "LARGE," and if it is smaller than
4
3
4 / inches (12 cm), select "SMALL."
4
• If you have selected "NO" for the subwoofer setting, you can only
select "LARGE" for the front speaker setting.
• If you have selected "SMALL" for the front speaker setting, you
cannot select "LARGE" for the center and rear speaker settings.
29
Center Delay Time Setting
Register the delay time of the sound from the center speaker,
comparing to that of the sound from the front speakers.
If the distance from your listening point to the center speaker is
equal to that to the front speakers, select 0 ms. As the distance to the
center speaker becomes shorter, increase the delay time.
• 1 msec increase (or decrease) in delay time corresponds to 11
• When shipped from the factory, the delay time is set to 0 ms.
On the front panel ONLY:
1. Press SETTING repeatedly until
2. Press CONTROL UP 5 /DOWN ∞
SETTING
Notes:
• Center delay time is not valid for the DVD MULTI playback mode.
• You cannot adjust the center delay time when you have set "CTR
CONTROL
Rear Delay Time Setting
DOWN UP
Register the delay time of the sound from the rear speakers,
comparing to that of the sound from the front speakers.
If the distance from your listening point to the rear speakers is equal
to that to the front speakers, select 0 ms. As the distance to the rear
speakers becomes shorter, increase the delay time.
• 1 msec increase (or decrease) in delay time corresponds to 11
NONE
• When shipped from the factory, the delay time is set to 5 ms.
On the front panel ONLY:
1. Press SETTING repeatedly until
2. Press CONTROL UP 5 /DOWN ∞
Notes:
• Rear delay time is not valid for the DVD MULTI playback mode.
• You cannot adjust the rear delay time when you have set "REAR
inches (30 cm) decrease (or increase) in distance.
"CTR DELAY" (Center Delay)
appears on the display.
The display changes to show the current setting.
to select the delay time of the
center speaker output (from 0 ms
to 5ms).
SPK" to "NONE."
inches (30 cm) decrease (or increase) in distance.
"REAR DELAY" appears on the
display.
The display changes to show the current setting.
to select the delay time of the rear
speaker output (from 0 ms to 15
ms).
SPK" to "NONE."
13 /
16
SETTING
CONTROL
DOWN UP
13
/
16
SETTING
CONTROL
DOWN UP