Page 1
AUDIO/VIDEO CONTROL RECEIVER AMPLI/TUNER DE COMMANDE AUDIO/VIDEO RX-8030VBK RX-7030VBK (For RX-8030VBK) (For RX-8030VBK) A/V CONTROL RECEIVER MENU ENTER 10/0 CONTROL INSTRUCTIONS For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear, MANUEL D’INSTRUCTIONS bottom or side of the cabinet.
Page 2
Warnings, Cautions and Others/ Mises en garde, précautions et indications diverses CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated...
Page 3
For U.S.A This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,...
Page 4
In addition, maintain the best possible air circulation as illus- Veiller également à ce que l’air circule le mieux possible comme trated. illustré. Spacing 15 cm or more Dégagement de 15 cm ou plus RX-8030VBK/RX-7030VBK Wall or obstructions Mur, ou obstruction Front Avant Stand height 15 cm or more...
COMPU LINK Remote Control System ..41 AV COMPU LINK Remote Control System ..42 Receiving Radio Broadcasts ......23 Operating JVC’s Audio/Video Components ... 44 Tuning in to Stations Manually ..........23 Using Preset Tuning ..............23 Operating Audio Components ..........44 Selecting the FM Reception Mode ...........
Introduction We would like to thank you for purchasing one of our JVC products. Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance from your unit, and retain this manual for future reference.
8 CATV/DBS CONTROL button (47) 9 TV/VIDEO button (46, 47) • When the remote operation mode changes, it is shown on p • For RX-8030VBK: CONTROL button (44 – 46) this display. • Signal transmission indicator (A) lights up when •...
EX / ES MODE FM/AM TUNING FM/AM PRESET FM MODE MEMORY INPUT INPUT ANALOG DIGITAL DIGITAL S-VIDEO VIDEO L—AUDIO—R INPUT ATT TUNER CONTROL VIDEO Only for RX-8030VBK Inside the front door How to open the front door Press down on PUSH OPEN.
Page 9
TAPE/CDR, FM, AM 7 MASTER VOLUME control (18) a ADJUST button (31) 8 • For RX-8030VBK: CC CONVERTER button and lamp (21) s ANALOG DIRECT button and lamp (21) • For RX-7030VBK: BASS BOOST button and lamp (22) 9 SUBWOOFER OUT ON/OFF button (19)
Rear Panel RX-8030VBK AUDIO VIDEO DIGITAL IN PREOUT COMPU LINK-4 VIDEO S-VIDEO COMPONENT VIDEO SUBWOOFER CENTER RIGHT LEFT SURR BACK SURR CENTER FRONT (SYNCHRO) COMPULINK- ANTENNA FRONT TV SOUND SURR DIGITAL 1 (DVD) (REAR) SUBWOOFER LOOP MONITOR (REC) (REC) DIGITAL 2 (CD)
Page 11
SURROUND SPEAKERS terminal (10) e CENTER SPEAKER terminal (10) r FRONT SPEAKERS 1 terminals (10) t FRONT SPEAKERS 2 terminals (10) Ô Earth (ground) terminal (11) Differences between RX-8030VBK and RX-7030VBK : Supplied : Not supplied PREOUT jacks CC Converter...
Getting Started This section explains how to connect audio/video components and speakers to the receiver, and how to connect the power supply. If the remote control cannot transmit signals or operate the receiver Before Installation correctly, replace the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.
AM Antenna Connections Basic connecting procedure 1 Twist and remove the insulation at Turn the loop until you have the the end of each speaker signal cable best reception. (not supplied). 2 Open the speaker terminal. ANTENNA AM Loop Antenna LOOP (supplied) Snap the tabs on the loop into the slots...
• Rear terminals of RX-8030VBK are used for explanation. Front speakers 1 Front speakers 2 Right Left Right Left Surround back speakers* Center speaker Right / Left CAUTION : SPEAKER IMPEDANCE CAUTION : SPEAKER IMPEDANCE SINGLE USE See Instruction Manual For Connection –...
Enhancing your audio system Connecting Audio/Video Components RX-8030V ONLY —Only for RX-8030VBK When connecting individual components, refer also to the manuals You can use this receiver as the pre-amplifier (control amplifier) supplied with them. when you connect power amplifiers to the PREOUT jacks on the rear using cables with RCA pin plugs (not supplied).
Page 16
CD recorder CD player To listen to the sound after connection, press CDR (for To listen to the sound after connection, press CD. RX-8030VBK) or TAPE/CDR (for RX-7030VBK). For RX-8030VBK RX-8030VBK/RX-7030VBK CD player RX-8030VBK CD recorder To audio input To audio output...
Page 17
CD recorder. When connecting an MD recorder to the TAPE/ frequently. CDR jacks, see page 12. • Though your MD recorder is one of JVC products with the COMPU LINK remote control system, you cannot use the COMPU LINK remote control system to operate the connected MD recorder.
Page 18
TV and/or DBS tuner To listen to the sound after connection, press VCR 1 or VCR 2 (for To listen to the sound after connection, press TV SOUND/DBS (or RX-8030VBK) or VCR (for RX-7030VBK). TV/DBS on the remote control). For RX-8030VBK You can connect two VCRs—one to the VCR 1 jacks and the other...
Page 19
• When you connect a DVD player with stereo output jacks: output (5.1-channel reproduction) jacks: To listen to the sound after connection, press DVD. To listen to the sound after connection, press DVD MULTI. COMPONENT VIDEO COMPONENT VIDEO RX-8030VBK/RX-7030VBK RX-8030VBK/RX-7030VBK VIDEO AUDIO VIDEO S-VIDEO...
DIGITAL OUT (optical) terminal on the rear. • For RX-8030VBK: Another digital optical input terminal is Digital optical cable (not supplied) located on the front panel (see page 13).
The STANDBY lamp lights up. Notes: • For RX-8030VBK: When connecting an MD recorder (to the TAPE/ Note: MD jack) and a DBS tuner (to the TV SOUND/DBS jacks), change A small amount of power is consumed in standby mode. To turn off the source names shown on the display.
TV until you select another video source. Press one of the audio source selection buttons while viewing the picture from a video component such as the VCR or DVD SUBWFR player, etc. For RX-8030VBK FM/AM TAPE/MD PHONO PHONO...
• Before turning on speakers again, as its high volume may come out DVD, VIDEO, TV (SOUND)/DBS, • For RX-8030VBK: of the speakers. CD, CDR, or TAPE/MD* DVD, TV (SOUND)/DBS, CD, or •...
2. Press INPUT DIGITAL (or ANALOG/DIGITAL Setting the Dynamic Range INPUT on the remote control) to select “DGTL AUTO.” You can enjoy a powerful sound at night using the Midnight Mode. The DIGITAL AUTO indicator lights up on the display. DIGITAL AUTO SUBWFR DIGITAL...
ONLY 1. Press TAPE/MD. • Make sure “TAPE” appears on the display. JVC’s CC (Compensative Compression) Converter eliminates jitter and ripples, achieving a drastic reduction in digital distortion by 2. Press and hold TAPE/MD until “ASSGN MD” appears on processing the digital music data in 24 bit–quantization and by the display.
Using the Sleep Timer The following basic operations are possible only using the remote control. Using the Sleep Timer, you can fall asleep while listening to music. When the shut-off time comes, the receiver turns off automatically. BASS BOOST Reinforcing the Press SLEEP repeatedly.
Receiving Radio Broadcasts You can browse through all the stations or use the preset function to go immediately to a particular station. Tuning in to Stations Manually Using Preset Tuning 1. Press FM or AM to select the band. Once a station is assigned to a channel number, the station can be The last received station of the selected band is tuned in.
To tune in a preset station Selecting the FM Reception Mode On the front panel: When an FM stereo broadcast is hard to receive or noisy, you can change the FM reception mode while receiving an FM broadcast. 1. Press FM or AM to select the band. •...
Basic Settings Some of the following settings are required after connecting and positioning your speakers while others will make operations easier. You can use QUICK SPEAKER SETUP to easily set up your speaker configuration. 3. Press in MULTI JOG (PUSH SET). Setting the Speakers Configuration Remote “ROOM SIZE?”...
Notes: These items can be set using Quick Speaker Setup. SMALL Speaker Distance This setting is only for RX-8030VBK. 2.4 m (8 ft) For RX-7030VBK, it is automatically set according to your “DGTL IN 2.4 m (8 ft) COAX” setting.
Basic Procedure : shows the initial setting in the following tables. Setting the Speakers To obtain the best possible surround effect from the Surround and DSP modes, register the setting about the speaker arrangement after all connections are completed. • If you have used Quick Speaker Setup on page 25, this setting is not required.
Setting the Speaker Distance Setting the Bass Sounds The distance from your listening point to the speakers is another You can adjust subwoofer and bass sounds precisely according to important element to obtain the best possible sound of the Surround your preference.
0dB: Normally select this. − − − − − 10dB: Select when the bass sound is distorted. • For RX-8030VBK: DVD (initial setting), MD*, CDR, TV (or DBS**) or CD. • For RX-7030VBK: DVD (initial setting), CD, TV (or DBS**) Selecting main or sub channel—DUAL MONO...
Memorizing the Volume Level for Each Source For RX-7030VBK: As you set the components connected to the digital coaxial This unit memorizes some settings separately for each source. terminal (DIGITAL IN 1), the optical terminals (DIGITAL IN 2 In addition, you can store the volume level for each source with the –...
Adjusting Sound You can make sound adjustment to your preference after completing basic setting. Basic Setting Items Basic Procedure On the following pages, you can adjust the items listed below: • You can adjust only the items applicable to the current sound mode.
Adjusting the Equalization Patterns Adjusting the Speaker Output Levels You can adjust the equalization patterns to your preference. You can adjust the speaker output levels. The test tone comes out of • Once you have made adjustment, it is memorized for each source. each speaker except subwoofer to check the output level balance when using the Surround mode.
Adjusting the Sound Parameters for the You can also use the remote control for adjusting the speaker Surround and DSP Modes output level. You can adjust the Surround and DSP sound parameters to your When using the remote control, you can make an adjustment preference.
Using the Surround Modes This unit activates a variety of Surround modes automatically. The basic settings and adjustments stored (see pages 25 to 33) are applied. Reproducing Theater Ambience Introducing the Surround Modes Dolby Digital* In a movie theater, many speakers are located on the walls to reproduce impressive multi-surround sounds, reaching you from all Dolby Digital is a digital signal compression method, developed directions.
Page 39
• If the surround speakers and center speaker are set to DTS-ES Matrix 6.1ch has been designed to add an extra surround “NONE” in the speaker setting, JVC’s original 3D-PHONIC channel to DTS Digital Surround 5.1-channel. By using a matrix processing (which has been developed to create the surround encoding/decoding method, an additional “surround back”...
Surround Modes Applicable to the Various Software Available Surround modes vary depending on the speaker settings and the incoming signals. The table below shows the relation of the Surround modes and the incoming signals (with the surround back speakers and EX/ES setting). •...
Activating the Surround Modes Activating the Surround Modes Available Surround modes vary depending on the speaker settings and the incoming signals. (See page 36.) Activating one of the Surround modes for a source automatically recalls the memorized settings and adjustments (see pages 25 to 33.) You can also use the buttons on the remote control for the same 1.
• If surround speakers are set to “NONE” in the speaker setting, “3D H PHONE” appears on the display and the DSP and JVC’s original 3D-PHONIC processing (which has been HEADPHONE indicators also light up. developed to create the surround effect through the front speakers only) is used.
ALL Channel Stereo mode Activating the DSP Modes This mode can reproduce a larger stereo sound field using all the connected (and activated) speakers. This mode cannot be used Activating one of the DSP modes for a source automatically without activating the surround speakers. recalls the memorized settings and adjustments (see pages 25 to •...
This receiver provides the DVD MULTI playback mode for reproducing the analog discrete output mode of the DVD player. Activating the DVD MULTI Playback Mode Connection diagram COMPONENT VIDEO RX-8030VBK/RX-7030VBK 1. Press DVD MULTI so that “DVD MULTI” appears on the display. VIDEO AUDIO...
COMPU LINK Remote Control System The COMPU LINK remote control system allows you to operate JVC’s audio components through the remote sensor on the receiver. Automatic Source Selection To use this remote control system, you need to connect JVC’s audio...
The AV COMPU LINK remote control system cannot control the DBS tuner. • For RX-8030VBK: Connect the VCR to the VCR 1 jacks. Video components connected to the VIDEO and VCR 2 jacks on the receiver cannot be controlled with the AV COMPU LINK remote control system.
Page 47
When you turn on the receiver; The AV COMPU LINK remote control system allows you to use the • If the previously selected source is “VCR 1” (for RX-8030VBK) five basic functions listed below. or “VCR” (for RX-7030VBK), the TV and VCR will turn on automatically.
Operating JVC’s Audio/Video Components You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC’s components are preset in the remote control. Operating Audio Components Tuner You can always perform the following operations:...
Page 49
Note: You can use either source selection buttons or the control button (CONTROL for RX-8030VBK or TAPE/CDR CONTROL for RX-7030VBK) to activate the buttons for the target source. If you press one of the source selection buttons, the playing source also changes. On the other...
RX-8030V ONLY • When you press one of the source selection You can use either VCR 1 (for RX-8030VBK) or VCR (for RX- buttons, the operation mode appears on the 7030VBK) or the control button (CONTROL for RX-8030VBK or VCR display window.
1. Press and hold CATV/DBS the manufactures’ codes again. 2. Press CATV/DBS CONTROL. To change the transmittable signals for For RX-8030VBK: “CALL” appears on the display window of operating another manufacturer’s TV the remote control. 1. Press and hold TV 3 Enter a manufacturer’s code using buttons 1 –...
Page 52
(for RX-8030VBK) or 1. Press and hold AUDIO (for RX-7030VBK). 2 Press DVD. 2. Press VCR 1 (for RX-8030VBK) or VCR (for RX- For RX-8030VBK: “CALL” appears on the display window of 7030VBK). the remote control. For RX-8030VBK: “CALL” appears on the display window of 3.
Page 53
For TV For VCR Manufacturer Codes Manufacturer Codes Manufacturer Codes , 02, 13, Quelle 52, 53, 54, 55, , 26, 27, 28, 29, 58 14, 47, 74 56, 57, 58, 59, Aiwa 01, 02 Akai 01, 02 60, 61, 62, 63, Bell &...
Troubleshooting Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC’s service center. PROBLEM POSSIBLE CAUSE SOLUTION The display does not light up. The power cord is not plugged in.
Specifications RX-8030VBK Amplifier Video Video Input Sensitivity/Impedance Output Power Composite video: At Stereo operation 130 W per channel, min. RMS, driven into 8 Ω, DVD IN, VCR 1 IN, VCR 2 IN, TV SOUND/DBS IN, VIDEO: Front ch: 1 V(p-p)/75 Ω...
Page 56
RX-7030VBK Amplifier Video Video Input Sensitivity/Impedance Output Power Composite video: DVD IN, VCR IN, TV SOUND/DBS IN: At Stereo operation 1 V(p-p)/75 Ω 110 W per channel, min. RMS, driven into 8 Ω, Front ch: S-video: DVD IN, VCR IN, TV SOUND/DBS IN: 20 Hz to 20 kHz, with no more than 0.08% 1 V(p-p)/75 Ω...
Page 57
Système de commande à distance Utilisation de la minuterie d’arrêt ..........22 AV COMPU LINK ........42 Commande d’appareils audio/vidéo JVC ..44 Réception d’émissions de radio ....23 Commande d’appareils audio ........... 44 Accord manuel d’une station ........... 23 Commande d’appareils vidéo ...........
Introduction Nous vous remercions d’avoir acheté un de nos produits JVC. Avant d’utiliser cet appareil, veuillez lire attentivement et entièrement ce mode d’emploi afin d’obtenir les meilleures performances possibles de votre appareil, et conservez ce mode d’emploi à titre de référence.
8 Touche CATV/DBS CONTROL (47) 9 Touche TV/VIDEO (46, 47) • Quand le mode de télécommand est changé, il apparaît sur p • Pour le RX-8030VBK: Touche CONTROL (44 – 46) l’affichage. • L’indicateur de transmission de signal (A) s’allume quand •...
FM/AM TUNING FM/AM PRESET FM MODE MEMORY INPUT INPUT ANALOG DIGITAL DIGITAL S-VIDEO VIDEO L—AUDIO—R INPUT ATT TUNER CONTROL VIDEO Uniquement pour le RX-8030VBK Derrière la porte avant Comment ouvrir la porte avant Poussez vers le bas sur PUSH OPEN.
Page 61
4 Capteur de télécommande 5 Fenêter d’affichage (17) • Touche FM MODE (24) 6 • Pour le RX-8030VBK: Touches et témoins de sélection de • Touche MEMORY (23) y Uniquement pour le RX-8030VBK: Prises d’entrée source (17, 18, 19, 21, 23, 24, 37, 40)
Panneau arrière RX-8030VBK AUDIO VIDEO DIGITAL IN PREOUT COMPU LINK-4 VIDEO S-VIDEO COMPONENT VIDEO SUBWOOFER CENTER RIGHT LEFT SURR BACK SURR CENTER FRONT (SYNCHRO) COMPULINK- ANTENNA FRONT TV SOUND SURR DIGITAL 1 (DVD) (REAR) SUBWOOFER LOOP MONITOR (REC) (REC) DIGITAL 2 (CD)
Page 63
Prises CENTER SPEAKER (10) r Prises FRONT SPEAKERS 1 (10) t Prises FRONT SPEAKERS 2 (10) Ô Prise de mise à la terre (11) Différences entre le RX-8030VBK et le RX-7030VBK : Fourni : Non fourni Prises PREOUT Convertisseur CC Sources sélectionnables...
Pour commencer Cette section explique comment connecter les appareils audio/vidéo et les enceintes à l’ampli-tuner, et comment connecter l’appareil au secteur. Si la télécommande ne peut pas transmettre les signaux ou ne Avant l’installation commande pas correctement l’ampli-tuner, remplacez les piles. Utilisez deux piles sèches de type R6P(SUM-3)/AA(15F).
Connexion de l’antenne AM Procédure de connexion de base 1 Tordez et retirez l’isolant à Tourner le cadre jusqu’à l’obtention l’extrémité de chaque câble de de la meilleure réception. signal d’enceinte (non fourni). 2 Ouvrez la prise d’enceinte. ANTENNA Antenne cadre AM LOOP (fournie) Insérer les languettes du cadre dans les...
• Les prises arrières du RX-8030VBK sont utilisées pour l’explication. Enceinte Enceintes avant 1 Enceintes avant 2 centrale droite gauche droite / gauche Enceintes Surround arrière* droite gauche CAUTION : SPEAKER IMPEDANCE CAUTION : SPEAKER IMPEDANCE SINGLE USE See Instruction...
Amélioration de votre système audio Connexion des appareils audio/vidéo RX-8030V ONLY —Uniquement pour le RX-8030VBK Lors de la connexion de composants individuels, référez-vous aussi Vous pouvez utiliser cet ampli-tuner comme un préamplificateur aux modes d’emploi qui les accompagnent. (amplificateur de commande) quand vous connectez des...
Page 68
Platine cassette (REC) Pour écouter le son après la connexion, appuyez sur TAPE/MD (pour le RX-8030VBK) ou sur TAPE/CDR (pour le RX-7030VBK). (PLAY) Pour le RX-8030VBK Vous pouvez connecter une platine cassette ou un enregistreur de MD aux prises TAPE/MD. Pour la connexion d’un enregistreur de MD, référez-vous à...
Page 69
à la page 12. d’un appareil. • Même si vous enregistreur de MD est un appareil JVC muni du système de commande à distance COMPU LINK, vous ne pouvez pas utiliser le système de commande à distance pour commander l’enregistreur de MD.
Page 70
Pour écouter le son après la connexion, appuyez sur VCR 1 ou VCR Pour écouter le son après la connexion, appuyez sur TV SOUND/ 2 (pour le RX-8030VBK) ou sur VCR (pour le RX-7030VBK). DBS (ou sur TV/DBS sur la télécommande).
Page 71
(reproduction 5,1 canaux): sortie stéréo: Pour écouter le son après la connexion, appuyez sur DVD MULTI. Pour écouter le son après la connexion, appuyez sur DVD. COMPONENT VIDEO COMPONENT VIDEO RX-8030VBK/RX-7030VBK RX-8030VBK/RX-7030VBK VIDEO AUDIO VIDEO S-VIDEO SUBWOOFER...
– DIGITAL 4 (optique): Pour l’enregistreur de CD • Si vous souhaitez commander le lecteur CD ou l’enregistreur de CD (ou l’enregistreur de MD: uniquement pour le RX-8030VBK) en utilisant le système de commande à distance COMPU LINK, connectez aussi l’appareil en question comme décrit dans “Connexions analogiques”...
Remarques: télécommande). • For RX-8030VBK: Lors de la connexion d’un enregistreur de MD Le témoin STANDBY s’allume. (aux prises TAPE/MD) et d’un tuner DBS (aux prises TV SOUND/ DBS), changez le nom de la source qui apparaît sur l’affichage.
Appuyez sur une des touches de sélection de source audio SUBWFR pendant que vous regardez l’image d’un appareil vidéo tel que le magnétoscope, le lecteur de DVD, etc. Pour le RX-8030VBK FM/AM TAPE/MD PHONO PHONO TAPE/MD Quel indicateur s’allume dépend du réglage des enceintes (pour...
Assurez-vous de réduire le volume: DVD, VIDEO, TV (SOUND)/ • Pour le RX-8030VBK: • Avant de connecter le casque d’écoute ou de vous le mettre sur les DBS, CD, CDR ou TAPE/MD* oreilles, car un volume élevé peut endommager à la fois le casque et vos oreilles.
2. Appuyez sur INPUT DIGITAL (ou ANALOG/ Réglage de la plage dynamique DIGITAL INPUT sur la télécommande) pour choisir “DGTL AUTO”. Vous pouvez profiter d’un son puissant la nuit en utilisant le mode L’indicateur DIGITAL AUTO s’allume sur l’affichage. de minuit (Midnight). DIGITAL AUTO SUBWFR SPEAKERS 1...
• La mise en service de la fonction Analog Direct annule l’atténuation Pour changer le nom de source de “TAPE” sur “MD”: de l’entrée (page 20) (et le convertisseur CC pour le RX-8030VBK: 1. Appuyer sur TAPE/MD. ci-dessous).
Utilisation de la minuterie d’arrêt Les opérations de base suivantes sont possibles uniquement en utilisant la télécommande. En utilisant la minuterie d’arrêt, vous pouvez vous endormir tout en écoutant de la musique. BASS Quand l’heure d’arrêt arrive, l’ampli-tuner se met automatiquement BOOST Accentuation hors tension.
Réception d’émissions de radio Vous pouvez parcourir toutes les stations ou utiliser la fonction de préréglage pour aller directement à une station particulière. Accord manuel d’une station Utilisation de l’accord par préréglage 1. Appuyez sur FM ou AM pour choisir la bande. Une fois qu’une station est affectée à...
Pour accorder une station préréglée Sélection du mode de réception FM Sur le panneau avant: Quand une émission FM stéréo est difficile à recevoir ou parasitée, il est possible de changer le mode de réception FM lors de la 1. Appuyez sur FM ou AM pour choisir la bande. réception d’une émission FM.
Réglages de base Certains des réglages suivants doivent être effectués après la connexion et la disposition des enceintes tandis que d’autres rendront les opérations plus simples. Vous pouvez utiliser QUICK SPEAKER SETUP pour faciliter la configuration de vos enceintes. 3. Appuyez sur MULTI JOG (PUSH SET). Configuration des enceintes Remote “ROOM SIZE?”...
Ces éléments peuvent être réglés en utilisant la configuration rapide. SMALL Enceinte Distance Ce réglage est uniquement pour le RX-8030VBK. 2.4 m (8 ft) Pour le RX-7030VBK, il est réglé automatiquement en fonction du réglage “DGTL IN COAX”. 2.4 m (8 ft) 2.1 m (7 ft)
Procédure de base : Indique le réglage initial dans les tableaux suivants. Réglage des enceintes Pour obtenir le meilleur son Surround possible avec les modes Surround et DSP, il faut enregistrer des informations sur la disposition des enceintes après que leur connexion est terminée. •...
Réglage de la distance des enceintes Réglage des sons graves La distance de votre point d’écoute aux enceintes est un autre Vous pouvez ajuster précisément le caisson de grave et les sons élément important pour obtenir le meilleur son possible des modes graves selon vos préférences.
Normalement, choisissez ce réglage. − − − − − 10dB: Choisissez ce réglage quand les sons graves sont • Pour le RX-8030VBK: DVD (réglage initial), MD*, CDR, déformés. TV (ou DBS**) ou CD. • Pour le RX-7030VBK: DVD (réglage initial), CD, TV (ou DBS**) ou CDR.
Mémorisation du niveau de volume pour chaque Pour le RX-7030VBK: source Quand vous réglez les appareils connectés à la prise coaxiale numérique (DIGITAL IN 1), les prises optiques (DIGITAL IN 2 Cet appareil mémorise beaucoup de réglages séparément pour – 4) sont réglées automatiquement sur les appareils donnés chaque source.
Ajustment du son Vous pouvez ajuster le son selon vos préférences après avoir terminé les réglages de base. Éléments des réglages de base Procédure de base Sur les pages suivantes, vous pouvez ajuster les éléments décrits ci-dessous: • Vous pouvez uniquement ajuster les éléments applicables au mode sonore actuel.
Ajustement des courbes d’égalisation Ajustement des niveaux de sortie des enceintes Vous pouvez ajuster les courbes d’égalisation selon vos préférences Vous pouvez ajuster les niveaux de sortie des enceintes. La tonalité • Une fois que l’ajustement est réalisé, il est mémorisé pour chaque de sort de chaque enceinte à...
Ajustement des paramètres du son pour les Vous pouvez aussi utiliser la télécommande pour ajuster le niveau modes Surround et DSP de sortie des enceintes. Vous pouvez ajuster les paramètres du son des modes Surround et Lors de l’utilisation de la télécommande, vous pouvez réaliser DSP selon vos préférences.
Utilisation des modes Surround Cet appareil permet de mettre en service une variété de modes Surround automatiquement. Les réglages de base et les ajustements mémorisés (voir pages 25 à 33) sont appliqués. Reproduction de l’ambiance d’un cinéma Introduction des modes Surround Dans une salle de cinéma, beaucoup d’enceintes sont situées sur les Dolby Digital* murs pour reproduire un son multi-surround impressionnant vous...
Page 91
“NONE” dans le réglage des enceintes, le mode 3D-PHONIC • Vous pouvez utiliser le Surround virtuel à 6,1 canaux (Virtual 6.1- original de JVC (qui a été mis au point pour créer un effet channel Surround) lors de la lecture d’un support DTS-ES sans Surround uniquement à...
Modes Surround applicables à divers supports Les modes Surround disponibles varient en fonction des réglages des enceintes et des signaux entrant. Le tableau ci-dessous vous montre la relation entre les modes Surround et les signaux entrants (avec le réglage des enceintes Surround arrière et de EX/ES).
Mise en service des modes Surround Mise en service du mode Surround Les modes Surround disponibles dépendant des réglages des enceintes et des signaux entrant. (Voir page 36.) Mettre en service un mode Surround pour une source rappelle automatiquement les réglages et les ajustements mémorisés (voir pages 25 à...
• Si les enceintes Surround et l’enceinte centrale sont réglées sur “NONE” dans le réglage des enceintes, le mode 3D-PHONIC original de JVC (qui a été mis au point pour créer un effet Surround uniquement à partir des enceintes avant) est utilisé.
Mode ALL Channel Stereo Mise en service du mode DSP Ce mode peut reproduire un champ sonore stéréo très large en utilisant toutes les enceintes connectées (et en service). Ce mode ne Mettre en service un des modes DSP pour une source rappelle peut pas être utilisé...
Cet ampli-tuner possède un mode de lecture DVD MULTI permettant de reproduire le mode de sortie analogique discret du lecteur de DVD. Mise en service du mode de lecture DVD Schéma de connexion MULTI COMPONENT VIDEO RX-8030VBK/RX-7030VBK AUDIO VIDEO 1. Appuyez sur DVD MULTI de façon que “DVD VIDEO S-VIDEO...
Système de commande à distance COMPU LINK Le système de commande à distance COMPU LINK vous permet de commander les appareils audio JVC à travers l’ampli-tuner. Pour utiliser ce système de commande à distance, vous devez Sélection automatique de source connecter les appareils audio JVC à...
Cet ampli-tuner est muni du système AV COMPU LINK-III, qui possède une fonction supplémentaire pour commander les appareils vidéo JVC par les prises en composantes vidéo. Pour utiliser ce système de commande à distance, vous devez connecter les appareils vidéo que vous souhaitez commander en suivant les illustrations ci-dessous et la procédure de la page suivante.
Page 99
Quand l’ampli-tuner est mis sous tension; • Si la dernière source choisie est “VCR 1” (pour le RX-8030VBK) Le système de commande à distance AV COMPU LINK vous ou “VCR” (pour le RX-7030VBK), le téléviseur et le permet d’utiliser les cinq fonctions de base décrites ci-dessous.
Commande d’appareils audio/vidéo JVC Vous pouvez commander des appareils audio et vidéo JVC avec la télécommande de cet ampli-tuner car les signaux de commande des appareils JVC sont préréglés dans la télécommande. Commande d’appareils audio Tuner Vous pouvez toujours réaliser les opérations suivantes:...
Page 101
Remarque: Vous pouvez utiliser les touches de sélection de source ou la touche de commande (CONTROL pour le RX-8030VBK ou TAPE/CDR CONTROL pour le RX-7030VBK) pour activer les touches pour l’appareil source. Si vous appuyez sur une des touches de sélection de...
• Quand vous appuyez sur une des touches de sélection de source, le mode de télécommande Il est possible d’utiliser VCR1 (pour le RX-8030VBK) ou VCR (pour le apparaît sur la fenêtre d’affichage RX-7030VBK) ou la touche de commande (CONTROL pour le RX- 8030VBK ou VCR CONTROL pour le RX-7030VBK) pour activer les touches décrites ci-dessus.
Pour changer les signaux émettables pour 2. Appuyez sur CATV/DBS CONTROL. commander le téléviseur d’un autre fabricant Pour le RX-8030VBK: “CALL” apparaît sur la fenêtre d’affichage de la télécommande. 1. Maintenez pressée TV 3 Entrez le code du fabricant en utilisant les 2.
Page 104
1. Maintenez pressée AUDIO 8030VBK) ou VCR (pour le RX-7030VBK). 2 Appuyez sur DVD. 2. Appuyez sur VCR 1 (pour le RX-8030VBK) ou 3. Entrez le code du fabricant en utilisant les VCR (pour le RX-7030VBK). touches numériques 1 – 9 et 0.
Page 105
Pour le téléviseur Pour le magnétoscope Fabricant Codes Fabricant Codes Fabricant Codes , 02, 13, Quelle 52, 53, 54, 55, , 26, 27, 28, 29, 58 14, 47, 74 56, 57, 58, 59, Aiwa 01, 02 Akai 01, 02 60, 61, 62, 63, Bell &...
Guide de dépannage Utilisez ce tableau pour vous aider à résoudre les problèmes de fonctionnement quotidiens. Si certains problèmes ne peuvent pas être résolus, contacter un centre de réparation JVC. PROBLÈME CAUSE POSSIBLE SOLUTION L’affichage ne s’allume pas. Le cordon d’alimentation n’est pas branché.
Spécifications RX-8030VBK Amplificateur Vidéo Sensibilité d’entrée vidéo/Impédance Puissance de sortie Vidéo composite: Pendant une opération stéréo 130 W par canal, min. RMS, entraîné sur 8 Ω, DVD IN, VCR 1 IN, VCR 2 IN, TV SOUND/DBS IN, VIDEO: Ca. avant: 1 V(c-c)/75 Ω...
Page 108
RX-7030VBK Amplificateur Vidéo Sensibilité d’entrée vidéo/Impédance Puissance de sortie Vidéo composite: DVD IN, VCR IN, TV SOUND/DBS IN: Pendant une opération stéréo 1 V(c-c)/75 Ω 110 W par canal, min. RMS, entraîné sur 8 Ω, Ca. avant: S-vidéo: DVD IN, VCR IN, TV SOUND/DBS IN: 20 Hz à...