Sony BVP-900 Series Product Information Manual page 99

1) Control select block
a
LOCK
PARA
(a) LOCK button
Press and illuminate the button to disable controls except those in
the iris/master black control block. Press the button again to enable
the controls.
(b) PARA (parallel mode) button
This button is illuminated when Parallel mode is active, in which
simultaneous operation with another control panel is possible. When
this button is illuminated, all the buttons and controls on this panel
(except for the iris/master black control block) are active, even if the
PANEL ACTIVE button is not illuminated. If you press the button
when it is illuminated, the illumination is turned off and the Parallel
mode is canceled.
(c) MASTER and SLAVE buttons
When adjusting the white balance of multiple cameras in
Master/Slave mode, it is necessary to decide which is to be the
master camera and which are to be slave cameras. Press and
illuminate the MASTER button to specify the connected camera to be
the master. Press and illuminate the SLAVE button to specify the
connected camera to be a slave. The slave camera follows the master
camera settings. If you press a button when it is illuminated, the
illumination is turned off.
2) STANDARD button
When this button is pressed, it remains illuminated for several
seconds while the camera is initialized to its standard state. If the
button is pressed while illuminated, the camera reverts to the state
before the button was illuminated. For details, refer to the system
manual.
3) Camera/CCU function ON/OFF buttons
Various functions of the camera or the CCU-700A/700AP can be
turned on and off from this panel. Functions except KNEE OFF, DTL
OFF, GAMMA OFF and CHROMA OFF are ON when the respective
buttons are illuminated.
CHAR
ACTER
5600K AUTO SKIN DETAIL
KNEE DETAIL GATE
KNEE DTL GAMMA
OFF OFF OFF
5600K: 5600K electronic color temperature conversion function
AUTO KNEE: Auto knee function. When this button is
illuminated, the knee point is automatically
adjusted according to the light content of the
picture.
SKIN DETAIL: Skin tone detail function.
DETAIL GATE: Skin tone detail gate function. When this
button is illuminated, the adjustment range of
the skin tone detail is displayed in white on the
b c
MASTER SLAVE
SAT BLACK CHROMA
GAMMA OFF
KNEE MONO COLOR
SAT COLOR CORRECTOR
Location and Function of Parts and Controls
monitor connected to the PIX (picture) output
of the CCU-700A/700AP.
SAT: Saturation function.
BLACK GAMMA: Black gamma function.
KNEE OFF: Knee compensation function. (OFF when the
button is illuminated)
DTL OFF: Detail compensation function. (OFF when the button
is illuminated)
GAMMA OFF: Gamma function. (OFF when the button is
illuminated)
CHRAMA OFF: Chroma function. (OFF when the button is
illuminated)
KNEE SAT: Knee saturation function.
MONO COLOR: Mono color function which mixes the chroma
signals of the signal hue to the luminance
signal. The chroma level is modulated
according to the luminance signal.
COLOR CORRECTOR: Color correction function for a defined
hue range.
CHARACTER: Self-diagnostic display function. When this
button is illuminated, the results of the CCU-
700A/700AP self-diagnosis are displayed on the
monitor connected to the CHARACTER
OUTPUT connector of the CCU-700A/700AP.
The results are also mixed with the video signal
output from the PIX1 OUTPUT connector. Each
time you press this button, the status changes as
follows.
OFF ON (page 1) ON (page 2)
The contents of the self-diagnosis can be displayed when required
even if this button is not illuminated.
4) ECS/Shutter control block
a
ECS
ON
ECS/SHUTTER
b
(a) ECS (Extended Clear Scan) button
Press and illuminate the button to set the camera to ECS mode.
Press again and turn off the illumination to set the camera to Shutter
mode.
(b) ON button
Turns the ECS function on and off (when the ECS button is
illuminated) or the shutter function (when the ECS button is not
illuminated). The selected function is ON when this button is
illuminated.
(c) ECS frequency/Shutter speed select buttons and displays
window
In ECS mode (when the ECS button is illuminated): The
selected ECS frequency is displayed in the window.
Press to select the desired scan frequency. The
frequency increases when the
and decreases when the
... ON (page n)
c
(up) button is pressed
(down) button is pressed. It
98
10