Sony BVP-900 Series Product Information Manual page 108

10
Location and Function of Parts and Controls
2: 1/4 ND
3: 1/8 ND
4: 1/16ND
5: 1:64 ND
(b) ND (ND filter select) buttons
Once either button is pressed, both buttons illuminate. Each time
you press the buttons, the ND filter setting changes as follows.
: 1 2 3 4 5 1 ...
: 5 4 3 2 1 5 ...
It continuously changes while either button remains pressed.
(c) CC (color temperature conversion filter select) display
Indicates the number corresponding to the selected CC filter.
A: Cross filter
B: 3200 K (clear)
C: 4300 K
D: 6300 K
E: 8000 K
(d) CC (color temperature conversion filter select) buttons
Once either button is pressed, both buttons illuminate. Each time
you press the buttons, the CC filter setting changes as follows.
: A B C D E A ...
: E D C B A E ...
It continuously changes while either button remains pressed.
Note Once you press any of the (b) and (d) buttons, all the four buttons
illuminate, enabling both the ND and CC filter selections.
(10) White balance/black balance control block
a
ABSOLUTE
b
WHITE
c
BLACK/FLARE
(a) ABSOLUTE button
Press and illuminate the button to change to the Absolute mode for
manual adjustment of the WHITE, BLACK, BLK GAMMA and
DETAIL controls. When this button is not illuminated, Relative mode
is automatically selected in the following cases.
* When an automatic setup is completed.
* When a scene file is retrieved.
When the PANEL ACTIVE button is not illuminated, or the PARA,
MASTER or SLAVE button is illuminated, Relative mode is always
selected and this button is not operative.
(b) WHITE (white balance manual adjustment) knobs
Used to manually adjust the white balance. From the left, the knobs
are for R, G, and B signal adjustment.
(c) BLACK/FLARE (black balance/flare balance manual adjustment)
knobs
Used to manually adjust the black balance (when the FLARE button
is not illuminated) or the flare balance (when the FLARE button is
illuminated). From the left, the knobs are for R, G, and B signal
adjustment.
(d) BLK GAMMA (black gamma) adjustment knob
107
Turn to adjust the black gamma.
(e) DETAIL adjustment knob
Turn to adjust the detail level.
(f) FLARE button
Toggles the black balance adjustment mode and flare balance
adjustment mode for the BLACK/FLARE knobs. Press and
illuminate the button to select the flare balance adjustment mode.
Press the button again so that it is not illuminated to adjust the black
balance.
11) Camera number/tally indication window
The number of the camera being controlled from this panel is
displayed in orange. When a red tally signal is sent to the camera,
the number is displayed in black and the background of the number
illuminates in red. When a green tally signal is sent to the camera,
the number is displayed in black and the background of the number
illuminates in green. When both the red and green tally signals are
sent simultaneously, the left half of the background illuminates in red
and the right half illuminates in green.
12) ALARM indicator
Illuminates when a problem occurs in the camera system and the
self-diagnostic function activates at the camera or the CCU-
700A/700AP.
13) PANEL ACTIVE button
Press and illuminate the button to permit this panel to control the
camera system (Panel active status). The IRIS/MB ACTIVE button
also illuminates.
14) CALL button
Press to send a call signal to the camera, on which the CALL button
is illuminated. The tally lamps on the camera and the red tally lamp
d
on the CCU-700A/700AP illuminate if not lit, or are turned off if they
BLK GAMMA
were already illuminated. When the CALL button on the camera is
e
pressed, the CALL button on this panel illuminates and a buzzer
DETAIL
sounds.
f
FLARE