Sony BVP-900 Series Product Information Manual page 88

10
Location and Function of Parts and Controls
Parallel mode is canceled.
(c) MULTI indicators
Show the Master/Slave status of the corresponding cameras 1
through 12 (when the EXPAND button is not illuminated) or 13
through 24 (when the EXPAND button is illuminated). The indicator
for the camera which is specified as the master for Master/Slave
mode illuminates green. The indicators for the slave cameras are
illuminated orange. This turns to red during the auto set-up of the
corresponding cameras. If an error occurs during the auto set-up and
the operation is interrupted, they flash in red.
(d) TALLY indicators
Show the tally status of the corresponding cameras 1 through 12
(when the EXPAND button is not illuminated) or 13 through 24
(when the EXPAND button is illuminated). The corresponding
indicator illuminates in red when a red tally is sent to a camera, and
it illuminates in green when a green tally is sent. When both red and
green tally are sent, it illuminates in orange. When a call signal is
sent to the camera, the indicator rapidly flashes in red.
(e) Active indicators
Show the control status of the corresponding cameras 1 through 12
(when the EXPAND button is not illuminated) or 13 through 24
(when the EXPAND button is illuminated). The indicators for the
cameras under control of this unit illuminate in green and the
indicators for the cameras under control of another control panel
illuminate in orange. An indicator whose corresponding camera (or
camera control unit) is not connected does not illuminate. An
indicator illuminates in red when an error is detected and the self-
diagnostic functions are activated in the corresponding camera or
camera control unit.
(f) Camera select buttons
Select the cameras to be controlled from this unit. Press and
illuminate the button corresponding to each desired camera.
Cameras 1 through 12 are selected when the EXPAND button is not
illuminated, and cameras 13 through 24 are selected when the
EXPAND button is illuminated.
(g) EXPAND button
Press to select the group to be selected with the camera select
buttons. Cameras 1 through 12 can be chosen when their select
buttons are not illuminated, and cameras 13 through 24 can be
chosen when their buttons are illuminated.
Note The CNU-700 Camera Command Network Unit is required to control
multiple cameras using the camera select function.
15) Filter control block
a
1 2
FILTER CTRL
A B
(a) FILTER CTRL (filter control) button
Press and illuminate the button to enable filter selection with the CC
and ND filter select buttons of this unit.
(b) ND (ND filter select) buttons
While the FILTER CTRL button is illuminated, press and illuminate
87
b
3 4 5
ND
C D E
CC
c
one of these buttons to select the corresponding ND filter.
1: Clear
2: 1/4 ND
3: 1/8 ND
4: 1/16 ND
5: 1/64 ND
When the FILTER CTRL button is not illuminated, the button
corresponding to the filter selected at the camera is illuminated.
(c) CC (color temperature conversion filter select) buttons
While the FILTER CTRL button is illuminated, press and illuminate
one of these buttons to select the corresponding CC filter.
A: Cross filter
B: 3200 K
C: 4300 K
D: 6300 K
E: 8000 K
When the FILTER CTRL button is not illuminated, the button
corresponding to the filter selected at the camera is illuminated.
16) ECS/Shutter control block (left)
Gamma control block (center)
Master gain control block (right)
a
ECS
ON
ECS/SHUTTER
c
b
(a) ECS (Extended Clear Scan) button
Press and illuminate the button to set the camera to ECS mode.
Press again and turn off the button illumination to set the camera to
Shutter mode.
(b) ON button
Turns the ECS function on and off (when the ECS button is
illuminated) or the shutter function (when the ECS button is not
illuminated). The function is ON when this button is illuminated.
(c) ECS frequency/Shutter speed select buttons and display
window
In ECS mode (when the ECS button is illuminated): The
selected ECS frequency is displayed in the window.
Press to select the desired scan frequency. The
frequency increases when the
and decreases when the
continuously changes while either button remains
pressed.
In Shutter mode (when the ECS button is not
illuminated): The denominator of the selected step
shutter speed is displayed in the window. Press to select
the desired shutter speed. The speed is displayed in the
window. Press to select the desired shutter speed. The
speed increases when the
decreases when the
continuously changes while either button remains
pressed.
GAMMA MASTER GAIN
d e
(up) button is pressed
(down) button is pressed. It
(up) button is pressed and
(down) button is pressed. It