Epson LX-300+II RTP Service Manual page 115

EPSON LX-300+II/300+II RTP/1170II
Table A-13. EEPROM Address Map (continued)
Address Explanation
0: PC 437
1: PC 850
2: PC 860
3: PC 863
4: PC 865
5: PC 861
6: BRASCII
7: Abicomp
8: IS0 Latin 1
9: Roman 8
10: PC 437Greek
11: PC 852
12: PC 853
2EH,2FH Character table selection
13: PC 855
14: PC 857
15: (reserved)
16: PC 866
17: PC 869
18: ISO Latin 1T
19: ISO 8859-7
20: MAZOWIA
128: Italic U.S.A.
129: Italic France
130: Italic Germany
131: Italic U.K.
30H,31H (reserved)
1 to 255 by 0.0588 mm(1/432 inch),
32H Line Spacing
00H:4.2 mm(1/6 inch: same as default)
Auto line feed b0: Auto line feed
Auto tear off b1: Auto tear off
Skip over perforation b2: Skip over perforation
High speed draft b3: High speed draft
33H
----- b4: (reserved)
----- b5: (reserved)
Tear off without FF b6: Tear off without FF
----- b7: (reserved)
Software b0: Software
0 slash b1: 0 slash
Buzzer b2: Buzzer
----- b3: (reserved)
34H
Auto CR b4: Auto CR (IBM) 0: Off
----- b5: (reserved)
----- b6: (reserved)
----- b7: (reserved)
Appendix
QPIT Factory
Setting
Settings Settings
21: Code MJK
22: Bulgaria
23: Estonia
24: PC 774
25: ISO 8859-2
26: PC 866 LAT
27: PC 866 UKR
28: Hebrew7
29: Hebrew8
30: PC862
31: PCAPTEC
32: PC 708
0000H 0000H
33: PC 720
(PC 437) (PC 437)
34: PCAR864
35: PC 858
36: ISO8859-15
37: PC771
38: PC437 Slovenia
39: PC MC
40: PC 1250
41: PC 1251
132: Italic DenmarkI
133: Italic Sweden
134: Italic Italy
135: Italic Spain I
0000H 0000H
00H 00H
(4.2 mm) (4.2 mm)
0: Off 1: On
0: Off 1: On
0: Off 1: On
0: On 1: Off
00H 00H
0:Off 1: On
0: ESC/P 1: IBM 2380 Plus
0: Off 1: On
0: On 1: Off
00H 00H
1: On
EEPROM Address Map
Table A-13. EEPROM Address Map (continued)
Address Explanation
0: Auto I/F selection 2: Serial I/F
35H I/F mode selection
1: Parallel I/F
10: 10 sec.
Auto I/F wait time
36H 30: 30 sec.
setting
00: 10 sec.(same as default)
Serial baud rate b0-b2:Serial baud rate
0: 19200 bps
1: 9600 bps
2: 4800 bps
----- b3:(reserved)
Serial parity b4-b5:Serial parity
37H
0: None
1: Even
Serial data length b6:Serial data length
0: 8bit
ETX/ACK protocol b7:ETX/ACK protocol
0: Off
IEEE1284.4 for Parallel b0-b1:
I/F 0: Auto
IEEE1284.4 for USB I/F b2-b3:
0: same as "IEEE1284.4 for Parallel I/F"
1: Auto (for test) 2: On (for test) 3: Off (for test)
Input Buffer b4:
38H
0: On(64Kbyte) 1: Off(1 byte)
----- b5:(reserved)
Parallel I/F bidirectional b6:Parallel I/F bidirectional mode
mode 0: On
Pause Offline b7:Pause Offline
0: Off
39H *ACK timing data
*ACK timing data
3AH
(complement of 39H)
b0: LOAD/EJECT function
b1: LF/FF function
b2: TEAR OFF function
b3: Micro Adjust function
3BH Panel mask pattern 1
b4: (reserved)
b5: (reserved)
b6: (reserved)
b7: (reserved)
Revision D
QPIT
Setting
Settings
00H
3: USB I/F (Auto)
00H
(10 sec.)
3: 2400 bps 6: 300 bps 00H
4: 1200 bps 7: (reserved) (19200)
5: 600 bps
2: Odd (None)
3: Ignore
(8bit)
1: 7bit
1: On
00H
1: On (for test) 2: Off (Auto)
(On)
1: Off
1: On
00H
00H
00H
Factory
Settings
00H
(Auto)
00H
(10 sec.)
00H
(19200)
(None)
(8bit)
00H
(Auto)
(On)
01H
FEH
00H
115