Table of Contents
Advertisement
Vivid910-hard-E00.fm 3 ページ ２００６年８月１７日 木曜日 午後１２時１０分
Notes On Use
• The VIVID 910 is designed for indoor use only, and should never be used outside.
• Use an AC power source which is within ±10% of the rated voltage.
• The VIVID 910 should be used within a temperature range of 10 to 40°C at a relative humidity of 65% or
less with no condensation.
∗For North America: VIVID 910 should be used within a temperature range of 10 to 40°C, and relative humidity 50%
• Do not use the VIVID 910 in direct sunlight or near sources of heat such as stoves. Doing so will cause the
temperature of the VIVID 910 to rise considerably higher than room temperature and may result in malfunc-
tions. Use the VIVID 910 in a well ventilated area and make sure that the ventilation holes of the VIVID 910
are not blocked.
• Do not use the VIVID 910 in extremely dusty or humid areas. Doing so may result in malfunctions.
• VIVID 910 is classified into a Pollution Degree 2 as instrument used in mainly in manufacturing plant, lab-
oratory, warehouse or equivalents. Use VIVID 910 in metal dust free and non condensing potential environ-
ment.
• VIVID 910 is categorized into Installation Category II as equipment connected to commercially available
power source.
• Do not subject the VIVID 910 to strong vibration or shocks. Doing so may result in malfunctions.
• Do not disconnect cords and cables with the POWER switch of the VIVID 910 set to ON "I". Doing so may
result in malfunctions.
• The VIVID 910 has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-
ference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference at his
own expense.
• The VIVID 910 is a class II instrument specified in IEC Publication 825. Use it according to the instructions
given in this manual.
• Do not use the VIVID 910 at altitudes of higher than 2000m.
• Contains Mercury in the backlighting of LCD used for display, Dispose According to Local, State or Federal Laws.
Care On Storage
• The VIVID 910 should be stored in areas with temperatures of between –10 and +50°C. Do not store it in
areas subject to high temperature or high humidity or where sudden changes in temperature or condensation
are likely to occur. We recommend storing the VIVID 910 at a relatively constant temperature with a desic-
cant (silica gel etc.).
• Do not leave the VIVID 910 inside a closed car or in the trunk of a car. Under direct sunlight, the increase in
temperature can be extreme and may result in malfunctions.
• The VIVID 910 should not be stored in areas where there is an excessive amount of dust, cigarette smoke or
chemical gas. Failure to adhere to this may result in performance degradation or break-down.
• Lenses that are not in use should be capped and kept in the lens case.
Notes On Cleaning
• If the VIVID 910 needs cleaning, wipe with a soft dry cloth. Never use solvents such as thinner or benzene.
• If the lens or laser emitting window is soiled with sand or dust, blow off the dirt using a blower, and wipe
them gently with a piece of cleaning paper dampened with cleaning agent.
• In cases of malfunction, do not disassemble the VIVID 910 or attempt to repair it yourself. Contact the near-
est KONICA MINOLTA SENSING-authorized service facility.
or less (at 40°C ) with no condensation..
3
Advertisement
Table of Contents
