Learning Of New Control Devices; Deletion Of Programmed Control Devices; Technical Data - Gemini 7590 User Manual

LEARNING OF NEW CONTROL DEVICES

ATTENTION: in order to carry out successfully the operation, it is
necessary to make the required electrical connections (door switch,
bonnet switch and positive under key).
The alarm can save to memory a maximum number of 12 control devices,
either radio controlled, or electronic keys, TAG cards or magnetic contact (the
later as a protection device).
Proceed as follows:
!
With the alarm being disarmed, open and keep open the bonnet and the
driver side door.
!
Turn the ignition key to "ON".
ATTENTION: the following operations must be carried out within four
seconds, otherwise the new device memorizing procedure will be
invalidated.
!
Turn the ignition key to "OFF".
Re-turn the ignition key to "ON" for three consecutive times (ignition key to
"ON" and "OFF"), within the maximum time of four seconds, as mentioned
before.
After the third commutation, let the ignition key to "ON".
!
The alarm will indicate the procedure starting of new control device or
magnetic contact learning, by two long turn signal flashes and two acoustic
signals, one acute tone and the other loud tone.
ATTENTION: do not modify the bonnet position, otherwise instead of
saving to memory new devices, deletion of existing ones in the alarm´s
memory will take place.
!
Now the alarm is waiting for receiving the device code.
!
Press the radio control push-button 1, introduce the electronic key in the
specific receptacle, press the TAG card button or make the magnetic
contact to transmit (bring near and then take away contact and magnet),
according to the device to be saved to memory.
In all four cases, the alarm will indicate the new device learning, by one turn
signal flashing and one acute tone signal.
!
Repeat the procedure to save to memory other devices.
!
Turn the ignition key to "OFF".
!
The procedure completion will be indicated by one long turn signal flashing
and one loud tone signal.
PAG. 12

DELETION OF PROGRAMMED CONTROL DEVICES

ATTENTION: in order to carry out successfully the operation, it is
necessary to make the required electrical connections (door switch,
bonnet switch and positive under key).
The alarm is equipped with a deletion procedure of new control devices, either
radio controlled, or electronic keys, TAG cards or magnetic contact (the later as
a protection device).
Proceed as follows:
!
With the alarm being disarmed, open and keep open the bonnet and the
driver side door.
!
Turn the ignition key to "ON".
ATTENTION: the following operations must be carried out within four
seconds, otherwise the new device deletion procedure will be
invalidated.
!
Turn the ignition key to "OFF".
!
Re-turn the ignition key to "ON" for three consecutive times (ignition key to
"ON" and "OFF"), within the maximum time of four seconds, as mentioned
before.
After the third commutation, let the ignition key to "ON".
!
The alarm will indicate the procedure starting of new control device or
magnetic or magnetic contact deletion, by two long turn signal flashes and
two acoustic signals, one acute tone and the other loud tone.
!
Close the bonnet.
!
The led will be illuminated constantly.
!
Keep the bonnet close till the moment, the complete deletion of devices
via radio, will take place (after about four seconds).
NOTE: keeping the bonnet close for less than four seconds, the device
deletion via radio will be unsuccessful.
!
The procedure completion will be indicated by led´s turning off, by one
long turn signal flashing and one loud tone signal.
!
Turn the ignition key to "OFF".
NOTE: the control device deletion does not imply any modification of

TECHNICAL DATA

Nominal tension
Nominal supply voltage range
Current absorption @ 12Vdc
Turn signal contact rating
Engine block contact rating
Alarm triggering
Max positive current with system armed (+A)
Sirene output current capacity
12 Vdc
¸
9 15Vdc
< 2mA with systme armed
and flashing led
10A a 20°C
8A a 20°C
30 sec.
700 mA
3A
PAG. 13