Table of Contents
Advertisement
PROGRAMMABLE FUNCTIONS
ACOUSTIC SIGNALS
This function allows the user to permanently exclude all acoustic signals. See
the relative paragraph for programming.
PANIC ALARM OR CAR-FINDER
If enabled, the PANIC ALARM function allows the user to activate the visual
and audio alarm signals deliberately by pressing key 2 on the remote.
This function works regardless of whether the alarm system is "ON" or "OFF".
The alarm signal lasts up to approx. 30". However, you can silence it at any
time by pressing key 2 on the remote again
While the alarm signal is emitted the LED emits a continuous light.
If during the programming phase, the PANIC function has been disabled, the
CAR FINDER function will be activated.
When the alarm is activated, the CAR FINDER function allows you to obtain a
short optic/acoustic signal by pressing button N°2 on the remote.
TThis function can be useful to look for the car in a parking lot or parking silo
without creating useless alarm condition.
The brief optic/acoustic signal consists of a low beep and the simultaneous
flashing of the turn indicators.
NOTE:
the emission of the audio signals is subordinate to their being enabled
when programming the accessory functions.
CURRENT ABSORPTION SENSOR
ATTENTION: before activating of the absorption sensor, it is suggested
to consult the specific rules being in force in your country (noise
pollution).
When the absorption sensor is activated, a signal will be sent out at any
minimal tension variation in the vehicle's electrical circuit (for example lamp
switching on).
ANTI-DISTRACTION FUNCTION AND DOOR LOCKING
This function determines the automatic activation of the system if this has been
disarmed and no voluntary actions are performed by the user (e.g. Door
opening).
The function prevents the vehicle from being left unprotected in cases where,
after the arming of the system, this is turned OFF accidentally by pressing the
button N°1 of the remote control.
The self rearming is confirmed by the alarm with visual/acoustic signalling (one
flash by the turn signals and one acoustic signal) .
The anti-distraction function activates the CDL control.
Therefore, in order to prevent involuntary activations of the system, it's
MANDATORY to connect the door pin switch to the system input
(BROWN/GREN wire of the alarm wiring harness).
NOTE: after disarming, a door opening will stop the function.
Together with the previously described function, the automatic door locking of
the vehicle is done when running.
PAG. 10
Being closed all the doors of the vehicle, turn the ignition key to "ON"; after 20",
all doors will be locked.
By turning the ignition key to "OFF", all doors of the vehicle will be automatically
unlocked.
To prevent this function from being activated accidentally, the system
continuously monitors the status of the ignition key and the input line of the
DOOR AND BOOT PUSHBUTTONS and therefore does not allow operation of
the locks if the DOORS and BOOT are opened manually while starting the
engine or during the 20" after starting it.
PASSIVE ARMING
Automatic arming allows to have the alarm system active, 45 seconds after the
engine switching "OFF".
After programming, this function is obtained simply by turning the ignition key
to "OFF".
The alarm will indicate the passive arming activation by a long flash of the turn
signals, two flash of the status led and two acoustic signals.
When opening a vehicle's door during passive arming, the arming time count
will be set to zero and the led will be permanently illuminated; when the door is
closed the 45" counting will restart.
LOCKING TIME
The standard locking time of the alarm is set to 0,5".
In case the vehicle needs a locking time of 6", you can vary this parameter
during the programming phase.
NOTE: When the comfort function has been activated, let the locking time set
to 0,5".
In fact, if the locking time is set to 6", when the alarm is disarmed, the windows
of the vehicle will open.
COMFORT CONTROL
The comfort control allows the automatic regulation of window closing, when
the alarm is armed.
In fact, after this function has been activated, at any alarm arming, the window
winder motor/control unit will receive a 25" command, to close the windows.
CDL DOUBLE OPENING PULSE
By enabling this function you will obtain, upon deactivation of the system, a
double control pulse on the door-unlocking line (about 0,5 second each).
This allows the opening of the centralized door locks on vehicles having the
diversified door opening (first pulse driver side door opening, second pulse
other doors opening).
This function is active only if the opening/closing time of 0,5" is selected, while
setting the opening/closing timo of 6" will automatically disabled the double
pulse.
PAG. 11
Hide quick links:
Advertisement
Table of Contents
