Page 1
I nstalled on bike model, number 953N USER AND INSTALLER MANUAL GEMINI Technologies S.r.l. Via Luigi Galvani 12 - 21020 Bodio Lomnago (VA) - Italy Tel. +39 0332 943211 - Fax +39 0332 948080 www.gemini-alarm.com Made in Italy ISO 9001 Certified company...
Replace the batteries: weak batteries will prevent the reference. remote control from properly operating the alarm system. The 953N alarm system cannot be paired with transponder The remote control has 2 buttons that activate several functions based on the TAG 908.
3.6 - ARMED CONDITION 3.0 - SYSTEM OPERATION - BASIC CONFIGURATION After the 20 sec. arming delay, the system is fully armed and ready to detect 3.1 - ARMING any irregularity. The LED will start flashing to confirm the armed condition. To arm the system, press remote control button “1”.
4.1 - OPTICAL/ACOUSTIC SIGNALS 3.10 - SYSTEM DISARMING WITHOUT ALARM MEMORY Operations such as arming/disarming, system programming, alarm memory To disarm the system, press remote control button “1”. The status LED will turn OFF and learning new devices are signaled both acoustically and optically (LED and disarming will be confirmed by 3 Beeps and 3 flashes of the turn indicators.
4.5 - ANTI-HIJACK FEATURE 5.0 - SLEEP MODE - ENERGY SAVER FEATURE To activate the anti-hijack feature while the engine is running, either: In order to preserve battery life, the system will automatically revert to sleep Press remote control button “1”. mode when the vehicle is sitting idle for a period of time.
7.0 - PIN CODE OVERRIDE 8.0 - PIN CODE OVERRIDE EXAMPLE If you cannot disarm the system from the remote controls because they are lost To help you understand the override procedure by PIN code, here below is a or broken or batteries are flat, you will be able to disarm the system by using the step-by-step example entering PIN code “2-3-4-1”.
9.0 - PIN CODE CUSTOMIZATION Simultaneously press both remote control buttons. The LED will turn OFF Here below is a step-by-step example showing how to customize the factory PIN code. In this case the selected PIN code is 2-3-4-1 isarm the alarm system Ground the BROWN-GREEN wire.
Do not use voltages other than the one specified by the manufacturer Protect the alarm from any direct water flow such as high-powered water jets found in a car wash. BATTERIES ATTENTION Gemini Technologies will not be held responsible for any damage caused by improper use. WARNING Use only CR1616 batteries.
INSTALLER MANUAL 17.0 - ALARM UNIT POSITIONING Since the alarm system has a built-in high sensitivity triaxial tilt sensor, it can 15.0 - FITTING INSTRUCTIONS be positioned either vertically or horizontally as long as you keep the following in mind Please read all instructions and understand them thoroughly before starting the installation.
18.0 - ACCESSORIES CAUTION Alarms are supplied without wiring harnesses. A wide range of specific pin- 18.1 - STATUS LED to-pin wiring harnesses is available for the most common motorbikes. Since the LED warning light serves as both a system status indicator and a The following tables refer to the generic wiring harness KITCA 417N17.
Turn ignition key in ON. 22.0 - DIODE INSTALLATION 2 flashes of the turn indicators and 2 confirmation tones (1 Bop and 1 Beep) How to tell if you need to install a diode: will acknowledge the system is in learn mode. Activate one of the turn indicators, turn ignition key OFF and arm the alarm.
After pressing both buttons simultaneously (step 4), program the features 24.0 - PROGRAMMABLE FEATURES according to your needs. To either enable or disable one of the programmable features, proceed as follows: TO ENABLE TO DISABLE NB: Remember to ALWAYS arm/disarm the system before programming. Press button 1 Press button 2 With the system disarmed, lift the seat...
26.0 - TILT SENSOR ADJUSTMENT 25.0 - PROGRAMMING EXAMPLE Here below is a step-by-step example showing how to program the system The alarm system has a built-in triaxial tilt/shock sensor with 4 levels of with the acoustic signals, the panic alarm and the pre-alarm features enabled. sensitivity adjustment.
Page 16
R&TTE Declaration of Conformity NOTES Doc ref. No. 2010-01 We, the undersigned, Company GEMINI TECHNOLOGIES S.r.l Address, City Via Luigi Galvani 12, 21020 Bodio Lomnago (VA) Country Italy Phone number +39 0332 943211 Fax number +39 0332 948080 Declare under our sole responsibility that the following equipment:...