Integra DTR-50.5 Instruction Manual page 75

■
Audio TV Out (Sub)
Off
On
This preference determines whether the incoming
audio signal is output from HDMI OUT SUB. You may
want to turn this preference on if your TV is
connected to HDMI OUT SUB and you want to listen
to the audio from a connected component through
your TV's speakers. Normally, this should be set to
"Off".
Note
• If "On" is selected and the audio can be output from the TV,
the AV receiver will output no sound through its speakers.
In this case, "TV Speaker" appears on the AV receiver's
display by pressing Display.
• This setting is fixed to "Off" when "Monitor Out" is set to
"Main" (➔ page 59).
• When "Monitor Out" is set to "Both" (➔ page 59), and this
setting is enabled, set audio output of source component to
2ch PCM.
• With some TVs and input signals, no sound may be output
even when this setting is set to "On".
• When "Audio TV Out (Sub)" is set to
listening through your TV's speakers, turning up the AV
receiver's volume control will make the sound be output
from the AV receiver's front left and right speakers. To stop
the AV receiver's speakers producing sound, change the
settings, change your TV's settings, or turn down the AV
receiver's volume.
• Listening mode cannot be changed when this setting is set
to "On" and the audio is output from the TV.
• When "Monitor Out" is set to "Both" (➔ page 59) and only
"Audio TV Out (Sub)" is set to "On", the audio is not output
from the TV connected to HDMI OUT SUB except in the
case the audio input is via HDMI.
• If the audio signal from the player is not supported by the
TV, the audio is not output from the TV even if this setting
is enabled. When the audio cannot be output from the TV,
(When "Monitor Out" is set to "Both", the audio cannot be
output form the TV connected to both HDMI OUT MAIN and
HDMI OUT SUB) the audio is output from the speakers
connected to the AV receiver.
■
Audio Return Channel
Off
Auto:
The audio signal from your TV tuner can be sent
to HDMI OUT MAIN of the AV receiver.
The audio return channel (ARC) function allows an
ARC capable TV to send the audio stream to HDMI
OUT MAIN of the AV receiver. To use this function,
you must select the TV/CD input selector and your TV
must be ARC capable. Default setting: "
Note
• This setting is fixed to "- - - - -" when the "HDMI CEC
(RIHD)" setting is set to "Off".
• This setting is set to "Auto" automatically when the "HDMI
CEC (RIHD)" setting is set to "On" for the first time.
• If you set "Audio Return Channel" to "Auto", the "Audio
Selector" settings of the TV/CD input selector will be
automatically switched to "ARC" (➔ page 70).
Tip
• After changing the settings of the "HDMI CEC (RIHD)",
"HDMI Through" or "Audio Return Channel", turn off the
power on all connected pieces of equipment and then turn
" "
On and you're
them on again. Refer to the user's manuals for all
connected pieces of equipment.
■
Lip Sync
Off
On
This function allows the AV receiver to automatically
correct any delay between the video and the audio,
based on the data from the connected monitor.
Note
• This function works only if your HDMI-compatible TV
supports HDMI Lip Sync.
■
InstaPrevue
These settings apply to "InstaPrevue" of the Home
menu
(➔ page 53)
HDMI video streams.
"
- - - - -
and specify the preview display of
En-75
Advanced Operations
Sub Window
Multi:
Displays preview thumbnails all at once.
Single:
Displays preview thumbnails one-by-one.
With this setting, you can set the number of preview
thumbnails displayed.
Position
(with "Sub Window" set to "Multi")
Top, Bottom, Left, Right
(with "Sub Window" set to "Single")
Upper Left, Upper Right, Lower Left, Lower
Right
With this setting, you can set the position of preview
thumbnails on the TV screen.
Note
• Depending on video signals, the picture may not be
properly rendered on the preview thumbnails of
InstaPrevue.
Auto Standby
■
Auto Standby
Off
On
When "Auto Standby" is set to "On", the AV receiver
will automatically enter standby mode if there is no
operation for 30 minutes with no audio and no video
signal input.
"Auto Standby" will appear on the AV receiver's
display and OSD 30 seconds before the Auto
Standby comes on.
Default setting: On (Australian models), Off (North
American models)
Note
On"
• Set to " , the Auto Standby function may activate itself
during playback with some sources.
Operating
procedure
(➔ page 58)