Display Modes And Setting Change Confirmation/Adjustment Progress Messages - Sony HDW-790 Operation Manual

VF DISP 2 page
Item Description
DISP IRIS Iris opening indicator
DISP ZOOM Zoom position indicator
DISP COLOR Displays the color temperature.
TEMP.
DISP BATT Displays the battery voltage/
REMAIN remaining capacity of an internal
battery pack or an external battery
connected to the DC IN
connector.
DISP DC IN Displayed when the power is
supplied from an external battery
connected to the DC IN
connector.
DISP WRR RF LVL Displays the reception level of the
wireless microphone.
DISP TIME CODE Displays the time code.
DISP FREEZE Displays the type of freeze-frame
picture.
1) For detailed information on the type of freeze-frame picture, see "5-
3-10 Using the Freeze Mix Function" on page 103.
3
Turn the MENU knob to move the
you want to set, then push the MENU knob.
b
The mark on the left of the selected item changes to
a z mark, and the z mark on the left of the setting
changes to a ? mark.
4
Turn the MENU knob to select whether the selected
item should appear in the viewfinder display (the ON
setting), or not appear (the "OFF" setting), then push
the MENU knob.
The z mark returns to a
returns to a z mark.
Note that pushing the CANCEL/PRST / ESCAPE
switch to CANCEL/PRST on this page has no effect.
5
To continue setting other items, repeat steps 3 and 4.
6
To end the menu operation, set the MENU ON/OFF
switch to OFF.
5-2-3 Display Modes and Setting
Change Confirmation/Adjustment
Progress Messages
You can limit or suppress the messages that give details of
setting changes and adjustment progress and results by
setting a display mode.
The conditions under which messages are displayed and
their correspondence with the display mode are as follows:
1)
b
mark to the item
b
mark, and the ? mark
Setting change confirmation/adjustment progress messages
and display modes
Y: Message is displayed.
N: Message is not displayed.
Message Message
display
conditions
When the filter ND : n, CC : m
selection has (where n = 1, 2, 3, 4,
been changed m = A, B, C, D)
When the gain GAIN : n (where n =
setting has been –3 dB, 0 dB, 3 dB, 6 dB,
changed 9 dB,12 dB, 18 dB, 24 dB,
30 dB, 36 dB, 42 dB)
When the WHITE : n
setting of the (where n = A CH, B CH,
WHITE BAL PRESET)
switch has been or ATW : RUN
changed
When the DCC : ON (or OFF)
OUTPUT/DCC
switch has been
set to DCC ON
or OFF
When the SS : 1/100 (or 1/125,
shutter speed 1/250, 1/500, 1/1000,
and mode
1/2000, ECS, SLS)
setting has been
1)
changed
When the black E.g. AWB : OK (For
or white balance details, see "4-1
has been Adjusting the Black
adjusted Balance and the White
Balance" on page 59.)
1) This is also displayed for about 3 seconds when the SHUTTER selector is
set to ON.
2) The shutter speed displayed depends on the selected frame frequency. For
details, see "4-2-1 Shutter Modes" on page 62.
Changing the display mode
You can change the display mode on the VF DISP 1 page
of the USER menu.
1
Follow steps 1 and 2 in "5-2-2 Selecting Display
Items" (page 84), until the VF DISP 1 page of the
USER menu appears on the screen.
2
Turn the MENU knob to move the
DISP MODE," then push the MENU knob.
b
The mark on the left of VF DISP MODE changes to
a z mark, and the z mark on the left of the setting
changes to a ? mark.
3
Turn the MENU knob until the desired display mode
appears, then push the MENU knob.
The z mark returns to a
returns to a z mark.
Status Display on the Viewfinder Screen
Display
mode setting
1 2 3
N N Y
N N Y
N N Y
N Y Y
N Y Y
2)
N Y Y
b
mark to "VF
b
mark, and the ? mark
85