Hdcp Status - Extron electronics PVS 405D User Manual

Command ASCII Command
(host to switcher)
EDID Minder
NOTES:
•
The switcher and PVT wallplate have two default EDIDs: 720p @ 60 Hz (digital), and 1024x768 @ 60 Hz (analog).
•
The default EDID of 720p @ 60Hz, 2‑CH is always present at inputs 1‑4 when no PVT wall plates are detected.
•
The firmware automatically uses default EDID of 1024x768 @ 60Hz for inputs 2 and 4 when a PVT SW HDMI RGB
D wall plate is detected
•
See the
EDID table
Assign EDID to
EAX1!*X1*EDID}
inputs
View assigned EDID
EAX1!EDID}
data
Capture display
ESX1*EDID}
EDID to custom
(user) slot (1‑4)
View/read EDID in
ERX1!EDID}
HEX format
View/read EDID
ENX1!EDID}
native resolution

HDCP status

View input HDCP
EIX1(HDCP}
View output HDCP
EOHDCP}
View all HDMI input
EIHDCP}
HDCP
HDCP input authorization (valid for HDMI inputs only)
HDCP Authorized
EEX1(*1HDCP}
device on
HDCP Authorized
EEX1(*0HDCP}
device off
Query HDCP
EEX1(HDCP}
Authorized Device
status
Verbose response
NOTE:
X1! = Input selection: 1 to 4
X1% = HDCP source status:
0 = Source detected but not HDCP compliant,
1 = Source detected and is HDCP compliant,
2 = No source detected, 3 = Unknown
X1^ = HDCP sink status:
0 = Source detected and is encrypted, sink is connected but not HDCP compliant,
1 = Source detected and is encrypted, sink is connected and is HDCP compliant,
2 = No sink detected,
3 = Source is not encrypted or detected, sink is connected but HDCP status is unknown
X1& = HDMI input HDCP Authorization status:
0 = Block HDCP encryption,
1 = Allow HDCP encryption (default)
X1* = EDID values. See the
X1( = HDCP input selection; inputs 1‑4 only.
X2) = EDID in HEX format: 128 or 256 Byte EDID raw HEX (text form)
X2! = Native resolution and refresh rate from selected EDID.
Response
(switcher to host)
on page 19 for X1* SIS symbol definitions.
EdidAX1!*X1*]
EdidAX1!*X1*]
EdidAX1!*X1*]
EdidSX1*]
X2)]
X2!]
HdcpIX1(*X1%]
HdcpOX1^]
Hdcp•X1%•X1%•X1%•X1%]
HdcpEX1(*1]
HdcpEX1(*0]
X1&]
HdcpEX1(*X1&]
table
on page 19 for values.
Additional Description
Assign EDID resolution and refresh rate
X1*
for input
View assigned EDID resolution and
refresh rate
Verbose mode response
Capture display EDID to
View assigned EDID resolution and
refresh rate
View assigned EDID native resolution
X2!
.
Query the input HDCP status
current input
Query the HDCP status
output.
Query the HDCP status
HDMI inputs (selected PVT wallplates).
Turn HDCP Authorized on for input
(default). Enables encryption support.
Turn HDCP Authorized device off for
X1(
input . Disables encryption support.
Query HDCP Authorized device status
X1(
for input
PVS 405D • SIS Communication and Control
X1!
.
X1* X1!
for input .
X1*
.
X2)
in HEX format.
X1%
of the
X1(
.
X1^
of the HDMI
X1%
of all the
X1(
.
26