Channel Level; Fader Function - Denon AVR-2309CI Owner's Manual

ENGLISH
<POWER>
I
ill
Svmbols used to indicate buttons in this manual
Sutton located on both the main unit and the remote control
unit
)0
BUTTON
Sutton only on the main unit
)0
<BUTTON>
Sutton only on the remote control unit
)0
[BUTTON]
<SPEAKERS>
<INPUT MODE>
~~r----I ';:f-~~----T""~[;]
QUICK SELECT <SELECT/ENTER>.
<H>
QUICK SELECT
--.!...:If'C1!fJiSJ
[Front]
Operations
1
Connect the HDMI to the AVR-2309CI with equipment
compatible with the HDMI control function (lI2Fpage
62).
2
Put the power on for all the equipment connected to
theHDMI.
3
Check the settings for all the equipment connected to
the HDMI and make HDMI available to them.
' * '
Please consult the operating instructions for the connected
equipment to check the settings.
' * '
Steps 1-3 do not have to be repeated once started.
' * '
Carryout steps 2 and 3 should any of the equipment be plugged
out.
4 Switch the television input to the HDMI connected to
the AVR-2309CI.
5
Switch the AVR-2309CI input to the HDMI input
source and check if the picture from the player is ok.
6
Put the television power on standby and check if the
AVR-2309CI goes into standby.
Channel Level
You can adjust the channel level either according to the playback
sources or to suit your taste, as described below.
1
Press
<SELECT/ENTER>
or
[CH SELECn.
Channe I Vo I ume
: SR
o.
OdB
C
o.
OdB
SBR
o.
DdB
FR
o.
OdB
SBL
o.
DdB
SW
o.
OdB
SL
o.
OdB
Fader
FRONT4:
~REAR
2
Use
f::,.
\1,
<SELECT/ENTER>
or
[CH SELECn
to select
the speaker.
The speaker that can be set switches each time one of the
buttons is pressed.
3
Use
<J l>
to adjust the volume.
' * '
In the case of a sub woofer, reducing the volume when it is at
"-12 dS" will change the setting to "OFF" (none).
-Nell.
When the input source is "iPod'; you cannot perform channel level
setting.
1
Press
<SELECT/ENTER>
or
[CH SELECT].
Fader Function
This function lets you adjust (fade) the sound from all the front or
rear speakers at once.
[Rear]
If the AVR-2309CI does not work please check the following.
-Is the menu "Manual Setup" - "HOMI Setup" - "HOMI Control"
(!2iT'page 32) set to "ON"?
- Is the menu "Manual Setup" -" HOMI Setup" - "Power Off Control"
(!2iT'page 32) set to "ON"?
- Is the control function used for the television HOMI properly set?
(Check the television operating instructions for details.)
- Should any of the operations below be performed, the interlocking
function may be reset, in which case, repeat step's 2 and 3.
• Menu "Input Setup" - "Assign" - "HOMI" ((Fpage 42) setting
has changed.
• There is a change to the connection between the equipment and
the HOM I, or an increase in equipment.
2
Press
f::,.
\1,
<SELECT/ENTER>
select "Fader".
or
[CH SELECn
to
63
3
Use
<J l>
to adjust the volume of the speakers.
(<J: front,
1>:
rear)
- The fader function does not affect the subwoofer.
- The fader can be adjusted until the volume of the speaker adjusted
to the lowest value is -12 dS.