Summary of Contents for PURE M3700
-
Page 1: User Manual
M3700 Pure SIP Gateway User Manual Version: 11.0 Firmware: 1.10 Update: 2006/05/12 DCC NO. 91710015011... -
Page 3: Table Of Contents
M3700 user manual Contents 1. Safety Instructions.................. 7 2. Preface..................... 7 What is SIP ......................7 2.1.1 SIP Clients......................7 2.1.2 SIP Servers ......................8 3. Package Contents................... 9 4. Panel Descriptions ................. 9 Front Panel ......................9 Rear Panel......................10 LED Indicators ....................11 Connectors ......................12... - Page 4 Dialing Plan......................38 8.1.1 Dialing Method...................... 38 8.1.2 Dial In Rewriting Rule ................... 41 Call Forward ......................42 Inbound Authentication ..................43 FAX........................43 Non-SIP Call port seizure preference ..............44 Call Waiting......................45 Target the Media (RTP)..................47 9. WEB MANAGEMENT INTERFACE ............48 BASIC / GENERAL....................49 IP SETTING.......................51 ADVANCED / GENERAL ...................53 SIP COMMON ....................55...
- Page 5 Support Min-Expire time If the default expire time is shorter than Min-Expire time of Proxy from server for registration Server and server reply correct Min-Expire time message, M3700 adjust the Min-Expire time itself and register to SIP Proxy again. SIP Entity registration Register or De-register all SIP entity.
- Page 6 System can specify NAT WAN IP when the connection to STUN server without STUN server is disabled Add new dialing plan Digits dialed from M3700 can be rewrite to different digits and sent to control SIP Proxy. Add Country Region ID...
- Page 7 M3700 user manual generated automatically Add SIP-based T.38 Standard SIP-based T.38 is applied. T.38 Proprietary is not retained protocol Add Route control Default route call to outbound proxy if outbound proxy is enabled and Registrar is disabled. Change History: Software Version 1.04...
- Page 8 New Auto Answer function Disable Auto Answer, Auto Answer without PIN code, Auto Answer for Inbound transit call to with PIN code for inbound transit call control. Interpret T.38 and G.711 Explain the timing for T.38 and G.711 using in products FAX operation Interpret port seizure When make a non-SIP call, those preference will decide which port...
-
Page 9: Safety Instructions
M3700 Quick Installation Guide for installation first. If you have further configuration, you can refer to this manual. Preface The M3700 unit is a personal SIP VoIP gateway developed using the latest in VoIP technology. It is also very simple to install and easy to operate. 2.1 What is SIP 2.1.1... -
Page 10: Sip Servers
It support SIP standard and can register to SIP Proxy. If wireless LAN connection keeps, the Phone can make calls in certain range without wiring. 2.1.2 SIP Servers SIP servers include the following: (1) Proxy server—The proxy server is an intermediate device that receives SIP requests from a client and then forwards the requests on the client's behalf. -
Page 11: Package Contents
M3700 user manual Package Contents The M3700 Gateway Power Core Accessories for fixing support (For 3708/3716) System CD-ROM 5 IDC Connector (For 3708/3716) Rubber footer RJ-45 Ethernet Cable RJ-11 Telephone Cable Panel Descriptions 4.1 Front Panel REGISTERED STUN M3716 Front Panel... -
Page 12: Rear Panel
4.2 Rear Panel There is a button on the rear panel of gateway for special maintenance. Please don’t touch this button under normal operation. M3716 Rear Panel M3708 Rear Panel M3704A Rear Panel M3704B Rear Panel M3704C Rear Panel M3704D Rear Panel... -
Page 13: Led Indicators
M3700 user manual M3702A Rear Panel M3702B Rear Panel 4.3 LED Indicators Label Description 10/100 LNK/ACT Link up Ethernet Link down Flash Sending/Receiving data packets 100Mbps On (LNK is on) 100Mbps Off (LNK is on) 10Mbps LOOP/RING Off hook On hook... -
Page 14: Connectors
4.4 Connectors Ports Label Description Voice Ports Connects to a telephone set or fax machine Connects to the phone line Ethernet LAN/Internet RJ-45 connector Ports MDI-X connects to a Modem RJ-45 connector MDI connects to a PC Console Port Console RJ-45 connector/RS-232 Interface (Only 3704/3708/3716) 4.4.1... -
Page 15: Idc Connectors (Only For 3708/3716)
M3700 user manual If Console cable is not available, run Telnet in PC for connection is OK. 4.5 IDC Connectors (Only for 3708/3716) IDC connector is used for the voice interface (FXS and FXO) on the frame model. IDC connector can easily connect PBX line and telephone wire together to the gateway. -
Page 16: Information Required Before Installation
Information required before Installation You need to prepare the following information before installing the gateway. 5.1 IP Address The gateway requires an IP address for operation. Before installation you need to know how to obtain an IP address from your local ISP. Static IP, DHCP or PPPoE can be used. The following table helps you to decide what information you need. -
Page 17: Sip Information
M3700 user manual 5.2 SIP Information Before configuring SIP, the M3700 requires SIP information for operation. The following table helps you to decide what information you need. Items Description 1. SIP Proxy If you want to make SIP calls through SIP proxy server, you will need to know the IP address or domain name of SIP proxy server. -
Page 18: Confirming The Region Id
2. Configure IP address of gateway. 3. Enter into the WEB page. 4. Plan and configure the channels into SIP entity. (if needs. By default, all channels joins Entity 1) 5. Configure SIP proxy and registrar information. 6. Configure SIP entity information. 7. -
Page 19: System Console Settings (Only 3704/3708/3716)
M3700 user manual 6.1.2 System console settings (Only 3704/3708/3716) The Instructions below is to set Region ID from Console terminal or Telnet (For Telnet, From Windows, Start Telnet 192.168.0.2 (192.168.0.2 is the default IP of this machine) (In the example, the Region ID is changed to 07 for China) SIP-RG>enable... -
Page 20: Static Ip Mode
6.2.1 Static IP Mode The following table shows an example. IP Address 210.67.96.121 Subnet Mask 255.255.255.248 Default Gateway 210.67.96.120 Web Management Password Using the information contained in the example above. The procedure is as follows: 1. Connect the unit to a suitable Power source. 2. -
Page 21: Dhcp Mode
M3700 user manual 6.2.2 DHCP Mode 1. Connect the unit to a suitable Power source. 2. Connect a traditional phone set to the “FXS” connector located on the rear panel. 3. When the CPU/ACT light is on, pick up the phone to hear the dialing tone. - Page 22 can find them at section 12.4 Mapping table of characters used in PPPoE. Example user name：83721@hinet.net，Password：123ab，The procedure is below 1. Connect the phone to the unit 2. When CPU/ACT is light, pick up the phone and press ；You will hear 3 short tones. 3.
- Page 23 M3700 user manual 3. When the CPU/ACT light is on, pick up the phone. You should hear the dialing tone. 4. ##0000 ; you should hear three short tones. 5. 15123 ; “123” is the web management password. 6. 010# ;...
- Page 24 After you have completed the PC’s IP address setting, you will be required to restart the PC in order for the new settings to take effect. Step 3: Using the browser to configure the PPPoE Parameters of the gateway. On the PC that is connected to the unit, enter the unit’s IP address (Default 192.168.0.2) and press enter.
- Page 25 M3700 user manual 6.2.3.4 Upon entering the web based configuration interface. Click on “IP SETTING” at the top of the page and you will see the page as shown in the following image. Select PPPoE from the “IP State” pull down menu.
- Page 26 Web Folder: BASIC\ Click the “Apply” button to apply any changes. At this stage, your unit should be able to use PPPoE to access the Internet. However, if you configured a wrong account number or password, your unit cannot access the Internet. You are not able to use PC to access unit by using the IP address of 192.168.0.2 because unit has been set in PPPoE mode.
-
Page 27: Sip Configuration
SIP Configuration M3700 not only can make regular PSTN calls, it also can communicate with IP Phones or Soft-Phones by using SIP protocol. This section shows you what parameters you need to configure for SIP calls and how to make the SIP calls. -
Page 28: Channels And Sip Entity
7.1 Channels and SIP entity Many Channels can be assigned as one SIP Entity. Single Channel also can be assign as one SIP Entity. Application example: As the figure below, Channel 1-3 belongs to SIP Entity 1: 001@abc.com. Channel 4 and Channel 5 belongs to SIP Entity 2: 002@abc.com. -
Page 29: Sip Proxy And Registrar Parameters
M3700 user manual Notice: Each channel must belong to a SIP entity. 7.2 SIP Proxy and Registrar Parameters You need to configure IP address or Domain name of Registrar and Outbound Proxy server (optional), please check the information is right. -
Page 30: Sip Entity
7.3 SIP Entity SIP service provider will assign one or more SIP accounts for you when you apply for the service. In standard, the SIP account is called ‘Public Address’, so you need to configure the account information in ‘Public Address’ item. The format is like an E-mail address such as mary@abc.com. The Public Address will be generated automatically with the format below if user keeps the Public Address empty. -
Page 31: Configure Stun For Client Under Nat
7.5 Configure STUN for Client under NAT STUN is an application-layer protocol that can determine the public IP Address of a NAT device that sits between the STUN client (M3700) and STUN server. Notice: 1. If your gateway is behind NAT (Use Private IP), please consult the SIP service provider to provide information of STUN server and also configure the parameter here, otherwise you need to input NAT WAN IP to penetrate NAT device Please refer to section 9.10 STUN after... - Page 32 Provider), their Outbound Proxy Server supports Media Relay, device under NAT can penetrate NAT without configuration. 3. STUN does not support Symmetric NAT. STUN Server NAT Device (Router, IP M3700 Internet sharing device) NAT WAN IP Configuration WEB Page: ADVANCED\STUN...
-
Page 33: Check Sip Entity Status
General Phone Book Since the SIP phone number is not easy for regular phone to dial, M3700 provide a SIP phone book to let standard phone to make a SIP call easier. The phone book uses index number to map SIP account. -
Page 34: Hotline Function
FXS channel user of M3700 picks up hand-set. ♦ If the FXS channel is Hotlined to M4600 SIP Line, (skip this section if the M3700 don't register to M4600 SIP Line) FXS channel user of M3700 hear dialing tone from M4600B SIP line when pick up hand-set, and then he/she can dial extension number to other SIP device or Outbound Call to PSTN via IP-PBX environment. - Page 35 M3700 user manual Hotline mapping table Channel (FXS) only Index Number Description FXS channel Index number “1” maps the 1 FXS channel FXS channel Index number “2” maps the 2 FXS channel …. …. … FXS channel Index number “16” maps the 16...
- Page 36 1001 to 1002. 1002 SIP Phone (Notebook) the unit SIP Line Entity: 1234567@61.22 M4600 M3700 0.145.70 1001 Hotline to M4600B SIP Line So we configure the Phone Book as below Index Public Address Port Via Proxy...
-
Page 37: Make Sip Calls
M3700 user manual 7.8 Make SIP Calls After you have configured the SIP phone on the SIP phone book, you can easily make SIP calls. You can select one way to make SIP call following these ways: Standard Call: Dial <numbers>+<#>. -
Page 38: Make Inbound Transit Call
Notice: If you do not want to dial “#” after numbers, please configure the ‘Dial Ending Time’ item. After the seconds configured here, the call will be sent automatically. WEB Page: ADVANCED\GENERAL 7.9 Make Inbound Transit Call To make an inbound transit call from PSTN to SIP, you have to enable Auto Answer function of this gateway Please enable Auto Answer configuration at WEB Page: CHANNEL... -
Page 39: Make Sip Ip Call Without Sip Proxy
M3700 user manual Dial Inbound Transit Call when Auto Answer is configured as Enable w/ PIN code This Auto Answer mode provides security control for the Inbound Transit call Please dial the number below after the second dial tone: 1. PIN code + ‘#’+ SIP Number + ‘#’, Example: 7742#73797# or 2. -
Page 40: Other Parameters
(2) Transparent: All numbers user dials are sent to SIP proxy server and all number that controls M3700 is disabled, including the end code # of each dialing. (3) Transparent with digitmap: All numbers user dials are sent to SIP proxy server and if any numbers match digitmap, number is send to SIP Proxy immediately without waiting dial end time. - Page 41 1. Able to create usable rule in digit map that is convenience for user to make calls. By this digit map, M3700 can simulate the FXS port of M4600 Plus. It also makes dialing behavior more easily. 2. When digit map is enabled, the outgoing call that fits the rule goes immediately and wait dial ending time is not required.
- Page 42 Then you are able to use the transparent function with digitmap. Transparent means all numbers user dials are sent to SIP proxy server and all number that controls M3700 is disabled, including the end code # of each dialing. By this way, all numbers user dials compare with the digitmap. When the number dialed matches the digit map, the number send to Proxy Server immediately without waiting dial ending time.
-
Page 43: Dial In Rewriting Rule
8.1.2 Dial In Rewriting Rule Number dialed from M3700 can be converted to different number and sent to SIP Proxy. User can pre-define maximum 10 sets of prefix rewriting rule to convert the number that user dials before build the connection to SIP Proxy. It is useful to create a user-friendly dialing behavior and also can limit user to dial certain number. -
Page 44: Call Forward
Country Code + Area Code + Phone No., and then sent to proxy, and prefix phone number 0204 is forbidden. Pattern Rewrite X means any digits. ! means the call is terminated. If the prefix number dials from user are 001~009, then the 3 digits are removed. -
Page 45: Inbound Authentication
WEB Page: ADVANCED \ SIP INBOUND AUTHENTICATION 8.4 FAX For M3700 software version 1.05 or above, SIP-based T.38 Fax protocol is applied. Any brand SIP gateway with SIP-based T.38 Fax protocol may transmit FAX with each other. T.38 is FAX protocol and it has better performance and better successful transmission rate. -
Page 46: Non-Sip Call Port Seizure Preference
SIP-based T.38. Note: If M3700 connects different SIP devices, some have T.38, but some use G.711 codec only, then user should enable G.711 codec support for FAX. Setup method is listed below: 1. The same step as above set Connect Device to Fax 2. -
Page 47: Call Waiting
M3700 user manual VOICE port Select VOICE port only From the lowest port number upward FAX port Select FAX port only From the lowest port number upward 2. Outbound to PSTN For the calls from FXS to FXO, the ports of the same "Connect Device" type will be the prior selection for the calls. - Page 48 Inbound transit call is configured on M3700 (please refer to 7.9 Make Inbound Transit Call), then Call Waiting function is available when user dials the SIP number of this M3700 gateway itself. If no inbound transit call function is configured, it is impossible to do call waiting function.
-
Page 49: Target The Media (Rtp)
RTP contact information (IP address, port number) is different from original RTP packet. This function selects different contact information for M3700 to send RTP Packets to other SIP device within far-end NAT. It designates whether to use the source contact information from the UDP/IP... -
Page 50: Web Management Interface
WEB MANAGEMENT INTERFACE The Tree Architecture of Web Management is shown below HOME BASIC GENERAL IP SETTING ADVANCED GENERAL SIP COMMON SIP OUTBOUND AUTHENTICATION SIP INBOUND ATHENTICATION STUN DIALING PLAN FILE TEMPLATE INBOUND TRANSIT (for gateway has FXO port. Gateway without FXO port does not have this page) CHANNEL PHONE BOOK... -
Page 51: Basic / General
M3700 user manual 9.1 BASIC / GENERAL Category Section Description Default Setting Information Region ID Display region ID.(Read only) Software Display software version.(Read only) Version BootRom Display BootRom Version.(Read only) Version Hardware Display hardware Version.(Read only) Version Card Type Display card type. (Read only) - Page 52 Time Time Select the time server to synchronize Registrar Configuration Source the time of this gateway ♦ Registrar: Get the time data from the Registrar Server. ♦ NTP Server: Get the time data from the NTP Server NTP Server Input the address if the system use NTP server as time synchronization source.
-
Page 53: Ip Setting
M3700 user manual 9.2 IP SETTING Category Section Description Default Setting IP Settings IP State The way to obtain IP address: Manual Manual: Entered by user (Static IP) Auto(DHCP): Assigned by DHCP server PPPoE: Assigned by PPPoE of Current Setting Display the configured IP 192.168.0.2... - Page 54 Change To Enter the IP address that will be used after next restart, Including: IP Address Subnet Mask Address Default Gateway (This item is used only on Manual mode of IP Setting.) PPPoE Account The user’s account of PPPoE Settings protocol, provided by ISP.
-
Page 55: Advanced / General
M3700 user manual 9.3 ADVANCED / GENERAL Category Section Default Setting Description Flash Button Flash Time System confirmed 200 msec “Flash” time. Touch Tone (DTMF) Duration The duration to send a 100 msec DTMF. Inter-digit The inter-digit time of 100 msec sending string of DTMF digits. - Page 56 Time long to end the dialing 1-10 (seconds) number if a ‘#’ digit is missing. T.38 Fax Relay Redundancy Number of times to retry T.38 Fax protocol. Use more Redundant packet when network is unstable. No Redundant packet 1 Redundant packet 2 Redundant packets 3 Redundant packets 4 Redundant packets...
-
Page 57: Sip Common
M3700 user manual 9.4 SIP COMMON Section Item Field Description Default Port and Header Port The control port number of SIP protocol. 5060 DCC NO. 91710015011... - Page 58 SDP: via SDP Symmetric RTP: via Symmetric RTP Register Expire Expires Configure the expire time of registration. 3600 M3700 keeps to register the SIP proxy before expire time to insure registration Codecs Selection Codec G.729AB: Mark the selection to Enable Enable Type G.729AB Codec...
- Page 59 M3700 user manual Section Item Field Description Default G.723.1: Mark the selection to Enable Enable G.723.1 Codec PCMU: Mark the selection to Enable Enable PCMU Codec (G.711 u Law) PCMA: Mark the selection to Enable Enable PCMA Codec (G.711 A Law)
- Page 60 Section Item Field Description Default Public Address Address Enter SIP phone number of the port. Empty Setting The phone number general assigned by SIP service provider. Default Account information for registering SIP Account Proxy Username: It may the same as your SIP number Password: Password for Authentication Confirm Password: Reconfirm...
-
Page 61: Sip Outbound Authentication
M3700 user manual Section Item Field Description Default Entity Show ‘+ ‘ means the SIP entity is for the Empty channel. 9.5 SIP OUTBOUND AUTHENTICATION Section Item Field Description Default SIP Outbound Maximum Maximum number of entries (Read Only) 50... -
Page 62: Sip Inbound Anthentication
Section Item Field Description Default Update Enter the information of outbound Empty Entry authentication Entity: Select an entity. Realm: Domain name or IP address. Username: Enter Username of authentication. Password: Enter password of authentication. Confirm Password: Enter password again for confirmation. Delete Delete the information of outbound Empty... - Page 63 M3700 user manual Section Item Field Description Default Maximum Maximum number of (Read Only) 20 entries allowed Entered Number of entries of (Read Only) 0 authentication entered. Entries List Display the entries (Read Only) Empty Entity: Which entity that you select.
-
Page 64: Dialing Plan
9.7 DIALING PLAN Section Item Field Description Default Dialing Method Control Dialing Plan: Use dialing plan rule Dialing Plan Transparent: All number dialed is passed to Proxy Server Transparent (with Digitmap): All number dialed is passed to Proxy Server with digit map control For the detail of this function, please refer to 8.1 Dialing Plan DIALING PLAN... - Page 65 Enter numbers. Example: 050. Empty Delete Entry Enter numbers for delete. Empty Dial In Rewriting Control Digits dialed from M3700 can be Disable Rule rewrite to different digits and sent to SIP Proxy. Enable/Disable Capacity The max set of rewrite number...
-
Page 66: File Template
File template is the text data of your customized configuration. You can keep it for backup purpose. Configure other M3700 with this text file can save time to re-configure it. For this purpose, copy all text in this page (does not include left title column), paste to Windows Notepad and save it as SIP33XX.MEM (for example, SIP3304.MEM. -
Page 67: Template Of Mem File
M3700 user manual This content of this file can be modified, then upload the file to Gateway. If there is lots of data need to create or modify, use this way can save lots of time. For the procedure to use FTP client to connect this gateway, please refer to 11.2 Software Update Note: After you had uploaded MEM file back to gateway, for those setting that need no to restart the machine, it will take effect immediately;... - Page 68 Codecs-Selection = "1111" # (G729:1000,G723:100,G711U:10,G711A:1) Codec-Priority = 0 #(0~23) (refer to webpage) Hotline-Control = 0 # (0/1, Disable/Enable) RTP-Base-Port = 10000 Time-Source = 1 # (0/1, Registrar/NTP Server) NTP-Server = "ntpserver.com" Time-Zone = 24 # (0~29) (refer to webpage) DayLight-Saving = 0 # (0/1, Off/On) [SIP-ENTITY] Entity-No = 1 Entity-Control = 1 # (0/1, Disable/Enable)
-
Page 69: Related Configuration At Web Page
M3700 user manual [SIP-INBOUND-INFO] Realm = "realm.com" [SIP-INBOUND-AUTH] # format: (entity username password), entity 0 for all 0 "username_for_all" "password" 1 "username_for_1" "password" [STUN] STUN-Server-Control = 0 # (0/1, Disable/Enable) NAT-WAN-IP = "223.223.223.223" STUN-Refresh-Time = 60 # unit: seconds [STUN-SERVER] # format: (ip_address port) 223.223.223.224 3478... - Page 70 Out-Proxy-Status = 1 # (0/1, Web Path: ADVANCED\SIP COMMON Disable/Enable) Out-Proxy-Port = 5060 Web Path: ADVANCED\SIP COMMON Registrar-Domain = "sip99.yip.com" Web Path: ADVANCED\SIP COMMON Registrar-Status = 1 # (0/1, Disable/Enable) Web Path: ADVANCED\SIP COMMON Out-Of-Band-DTMF = 0 # (0/1, Web Path: ADVANCED\SIP COMMON Disable/Enable) Incoming-Call-Screen = 0 # (0/1, Web Path: ADVANCED\SIP COMMON...
- Page 71 M3700 user manual For the sequence of selection, please refer to web page. Hotline-Control = 0 # (0/1, Disable/Enable) Web Path: PHONEBOOK RTP-Base-Port = 4000 Web Path: BASIC\GENERAL Time-Source = 1 # (0/1, Registrar/NTP Web Path: BASIC\GENERAL Server) NTP-Server = "ntpserver.com"...
- Page 72 Default-Account-User = "username" Web Path: ADVANCED\SIP COMMON Default-Account-PASS = "password" Web Path: ADVANCED\SIP COMMON RFC-2833-DTMF = 1 # (0/1, Web Path: ADVANCED\SIP COMMON Never/Negotiate) Forward-Address = "user2@registrar.com" Web Path: ADVANCED\SIP COMMON Forward-Type = 0 # (0/1/2/3, Web Path: ADVANCED\SIP COMMON None/All/Busy/No Answer) [CHANNEL-CONFIG] Configuration of Channel...
- Page 73 M3700 user manual Auto-Answer = 0 # (0/1/2, Web Path: Channel Disable/Enable/Enable w/Pincode) Call-Waiting = 0 # (0/1, Disable/Enable) Web Path: Channel T38-Fax = 1 # (0/1, No/Yes) Web Path: Channel Voice-Input-Gain = 0 # (0~12, -6~6) Web Path: Channel...
- Page 74 [SIP-INBOUND-AUTH] # format: (entity Configuration of SIP Inbound Authentication username password), entity 0 for all 1 "Lester" "1234" Web Path: ADVANCED\SIP INBOUND AUTHENTICATION 0 "Jack" "5678" Web Path: ADVANCED\SIP INBOUND AUTHENTICATION [STUN] Configuration of STUN STUN-Server-Control = 0 # (0/1, Web Path: ADVANCED\STUN Disable/Enable) NAT-WAN-IP = "0.0.0.0"...
-
Page 75: Inbound Transit
M3700 user manual Proxy(0/1, No/Yes) [TELEPHONY] Configuration of Telephony DIAL-END-TIME = 4 # (1~10) (refer to WEB Folder: ADVANCED\GENERAL webpage) T38-RELAY = 3 # (0~4) (refer to webpage) WEB Folder: ADVANCED\GENERAL 9.9 INBOUND TRANSIT Only FONEM3700 gateway with FXO port has this web page. - Page 76 Group Field Description Default Value Transit call Warning Time This gateway will send warning tone periodically to check if the line is still alive. If calling side fail to press any key after hearing the warning tone, the line will be disconnected. Release Call by This gateway will check the RTP packet Checking RTP...
-
Page 77: Stun
M3700 user manual 9.10 STUN Section Item Field Description Default STUN Server Control Enable or Disable STUN Server service. Disable NAT WAN IP Address Input this NAT WAN IP helps you to pass through NAT without using STUN server. The port number inside and outside NAT should be the same. - Page 78 Section Item Field Description Default STUN Server Maximum Maximum number of (Read Only) 5 Setting entries allowed Entered Number of entries of (Read Only) 0 STUN server that have been entered. List Display all of servers that (Read Only) have been entered. Add a stun server Empty IP Address: Enter IP address or Domain...
-
Page 79: Channel
M3700 user manual 9.11 CHANNEL Category Section Description Default Setting Channel Channel number: Information Channel Display port type. (Read only) Type Phone: FXS Interface, connect to telephone set or Fax machine. Line: FXO Interface, connect to phone line. DCC NO. 91710015011... - Page 80 Channel For FXS port: Enable Control Bothway: Can make and accept IP call and PSTN call from this channel Disable Disable all functions of this port. For FXO port: IN_Only: Accept calls from PSTN only Bothway: Accept call from PSTN or call dial from FXS Disable: Disable all functions of this port.
- Page 81 M3700 user manual Battery This mechanism will reverse Reverse the polarity promptly that help some PBX to identify the start and end of each call ON: Enable the function OFF: Disable the function Auto Answer This unit auto answer the call...
-
Page 82: Phone Book
9.12 PHONE BOOK Section Item Field Description Default Apply to Hotline Control Enable or Disable the hotline function to Disable M4600 SIP Line or other SIP device to make hotline call. SIP Phone Book Maximum Maximum number of entries (Read Only) 200 allowed Entered Number of entries of phone... -
Page 83: Use Private Ip (Behind Nat)
M3700 user manual Use Private IP (Behind NAT) Using a Private IP in a NAT Environment The unit is able to communicate with other units under a NAT environment using Private IP addresses on the LAN side of your IP Sharing device. However you must configure the IP Sharing device to treat the unit as a Virtual Server using UDP port 5060,2000. -
Page 84: File Management
File Management 11.1 File Types The naming convention to the file type of FONEM4496 is listed in the following table: File Name File Type Description SIP3302.CFG System SIP3304.CFG File of system configuration configuration file SIP33XX.CFG SIP3302.RUN SIP3304.RUN Executing file System Software SIP33XX.RUN SIP3302.WEB SIP3304.WEB... - Page 85 M3700 user manual Software Update by FTP for File Type RUN and WEB Execute FTP Client Software, e.g. CuteFTP Enter IP Address, User Name (default is FTP), Password (the password of FTP and Console is same, and the default is blank), and the Port Number to 21 Click button Connect to get connection between gateway and FTP Client.
- Page 86 Select the file with extension of .RUN and click button Upload and then Yes to overwrite. (Please notice that the file name must be same as the file name in the Gateway, e.g. .RUN SIP3304 After the file is overwritten (you may check if the time of the file is updated), Gateway has to run Cold Start to store the configure file, then the updating is effective.
-
Page 87: Appendix
M3700 user manual Appendix 12.1 Appendix A: Phone-Set Command Pick up the handset and listen for the dialing tone. Dial “##0000 and listen for three consecutive tones before setting the following parameters. After input the parameters, please dial ‘# to end the configuration. - Page 88 Change WEB 6 digits Password Change FTP 6 digits Password Register or 0: De-Register; 1: Register De-register (quit) the SIP Entity registration Listen for the IP (ending ”#” is not required) Address Listen for the Subnet (ending ”#” is not required) Mask Listen for the Default (ending ”#”...
-
Page 89: Appendix B: Console Command
M3700 user manual 12.2 Appendix B: Console Command User Exec commands Enable Turn on privileged commands Exit Exit from the EXEC Help Description of the interactive help system Show Show running system information show Show the IP address of domain name server... -
Page 90: Specifications
G.165/G.168 16ms Jitter buffer Adaptive jitter buffer management Gain control In/Out +/-6db Transport protocols RTP, RTCP Call control protocol Pure SIP Network Interface Two Ethernet ports and One console port (for 4,8,16 Number of ports ports models) Interface 10BASE-T/100BASE-TX Auto-negotiation Connectors... -
Page 91: Mapping Table Of Characters Used In Pppoe
M3700 user manual 12.4 Mapping table of characters used in PPPoE Character Digits to key-in Character Digits to key-in DCC NO. 91710015011... -
Page 92: 2.5 Region Id
12.5 Region ID Country Region ID Country Region ID Country Region ID Argentina France Singapore Australia Germany Slovenia Philippines Hong Kong South Africa Portugal India Spain Brazil Italy Switzerland Canada Japan Taiwan China Korea Thailand Russia Malaysia British Sweden Mexico Vietnam Netherlands Belgium...