Installation - Alpine IVA-W505 Owner's Manual

Installation
• If
B or C is used. make sure that there is a enough space depth wise
before installing the unit.
If
the unit is forcibly pushed into the
mounting sleeve. damage may occur.
Mounting Sleeve (Included)
Dashboard
~
. Face Plate*2 (Included)
<Mounting Hole Position>
Position B
_n~_~c
• Depending on the position chosen. the front panel will protrude
differently.
seal (Included)
Rear of the Unit
@
o
It
Caution
Do not block the unit's fan or heat sink, thus preventing
air circulation. If blocked, heat will accumulate inside
the unit and may cause a fire.
Air ventilation hole
Caution concerning the installation location
1
Before installing, make sure that the opening and
closing of the display will not interfere with
operation of the gear shift.
Movable Display
/
: ' (
Frnm"~
t---
Dashboard
Position A
2
Angle of installation
Install at an angle of between horizontal and 3D·.
Note that installing at an angle outside of this range
will result in a loss of performance and possibly
damage.
'"
'"
'.
'"
3
Remove the mounting sleeve from the main unit (see
"Removal" on page 85).
The unit can be installed in the mounting sleeve in
three positions by aligning its mounting holes (A to
C) on the sides of the unit. Position A will be used in
most cases. If B or C are to be used, the hole
positions need to be modified.
First, determine the mounting position in the
mounting sleeve, then affix the supplied seal (refer
to "How to use a Seal" (page 85».
Slide the unit into the mounting sleeve and secure it.
Front Panel
"""".,,. '+r-.
Dashboard
Position B
;'~~l
From 'oMI
!
~?-i- Dashboard
Position C
.1
If
the installed mounting sleeve is loose in the dashboard. the
pressure plates may be bent slightly to remedy the problem.
84-EN
Installation
• If
B or C is used. make sure that there is a enough space depth wise
before installing the unit.
If
the unit is forcibly pushed into the
mounting sleeve. damage may occur.
Mounting Sleeve (Included)
Dashboard
~
. Face Plate*2 (Included)
<Mounting Hole Position>
Position B
_n~_~c
• Depending on the position chosen. the front panel will protrude
differently.
seal (Included)
Rear of the Unit
@
o
It
Caution
Do not block the unit's fan or heat sink, thus preventing
air circulation. If blocked, heat will accumulate inside
the unit and may cause a fire.
Air ventilation hole
Caution concerning the installation location
1
Before installing, make sure that the opening and
closing of the display will not interfere with
operation of the gear shift.
Movable Display
/
: ' (
Frnm"~
t---
Dashboard
Position A
2
Angle of installation
Install at an angle of between horizontal and 3D·.
Note that installing at an angle outside of this range
will result in a loss of performance and possibly
damage.
'"
'"
'.
'"
3
Remove the mounting sleeve from the main unit (see
"Removal" on page 85).
The unit can be installed in the mounting sleeve in
three positions by aligning its mounting holes (A to
C) on the sides of the unit. Position A will be used in
most cases. If B or C are to be used, the hole
positions need to be modified.
First, determine the mounting position in the
mounting sleeve, then affix the supplied seal (refer
to "How to use a Seal" (page 85».
Slide the unit into the mounting sleeve and secure it.
Front Panel
"""".,,. '+r-.
Dashboard
Position B
;'~~l
From 'oMI
!
~?-i- Dashboard
Position C
.1
If
the installed mounting sleeve is loose in the dashboard. the
pressure plates may be bent slightly to remedy the problem.
84-EN