Alpine IVA-W505 Owner's Manual page 82

I
UNSUPPORTED
I
o
A sampling ratelbit rate not supported by the unit is used.
- Use a sampling ratelbit rate is supported by the unit.
Indication for DVDNideo CD
NO DISC
o
No disc is inserted.
- Insert a disc.
o
Although a disc is inserted, "NO DISC" is displayed and the unit
does not start to play or eject the disc.
- Remove the disc by following these steps.
Press OPEN for at least 3 seconds.
16)
o
Button operation on the unit or remote control is not possible.
- For some discs or playing modes, certain operations are not
possible. This is not a malfunction.
REGIONAL CODE
VIOLATION
o
Disc does not match regional code number.
- Load a disc that matches the regional code number.
I
LOADING ERROR
I
EJECT ERROR
I
o
Mechanism error.
I) Touch [EJECT] of DISC on the EJECTfTILT screen and
eject the disc.
If not ejecting, consult your Alpine dealer.
2) When the error indication remains after ejecting, touch
[EJECT] of DISC on the EJECTfTILT screen again.
If the error indication still does not turn off after touching
[EJECT] of DISC on the EJECTfTILTscreen for a few times,
consult your Alpine dealer.
DISC ERROR
o
Scratched disc, contaminated disc/poor recording/disc
incompatible with this unit.
- Touch [EJECT] of DISC on the EJECTfTILT screen.
- Change the disc.
EJECT DISC BEFORE
USING DVD·SETUP
o
The DVD setup operation was attempted when a disc is inserted
in the unit.
- Eject the disc before the DVD setup operation.
I
UNSUPPORTED
I
(DivX· mode)
o
A sampling ratelbit rate not supported by the unit is used.
- Use a sampling ratelbit rate that is supported by the unit.
80-EN
Indication for CD changer
HI-TEMP
o
Protective circuit is activated due to high temperature.
- The indicator will disappear when the temperature returns to
within operation range.
ERROR01
o
Malfunction in the CD Changer.
- Consult your Alpine dealer. Press the magazine eject button
and pull out the magazine.
Check the indication. Insert the magazine again.
If the magazine cannot be pulled out, consult your Alpine
dealer.
o
Magazine ejection not possible.
- Press the magazine eject button. If the magazine does not eject,
consult your Alpine dealer.
ERROR02
o
A disc is left inside the CD Changer.
- Press the eject button to activate the eject function. When the
CD Changer finishes the eject function, insert an empty CD
magazine into the CD Changer to receive the disc left inside
the CD Changer.
INO MAGAZINEI
o
No magazine is loaded into the CD Changer.
- Insert a magazine.
NO DISC
o
No indicated disc.
- Choose another disc.
I
UNSUPPORTED
I
o
A sampling ratelbit rate not supported by the unit is used.
- Use a sampling ratelbit rate is supported by the unit.
Indication for DVDNideo CD
NO DISC
o
No disc is inserted.
- Insert a disc.
o
Although a disc is inserted, "NO DISC" is displayed and the unit
does not start to play or eject the disc.
- Remove the disc by following these steps.
Press OPEN for at least 3 seconds.
16)
o
Button operation on the unit or remote control is not possible.
- For some discs or playing modes, certain operations are not
possible. This is not a malfunction.
REGIONAL CODE
VIOLATION
o
Disc does not match regional code number.
- Load a disc that matches the regional code number.
I
LOADING ERROR
I
EJECT ERROR
I
o
Mechanism error.
I) Touch [EJECT] of DISC on the EJECTfTILT screen and
eject the disc.
If not ejecting, consult your Alpine dealer.
2) When the error indication remains after ejecting, touch
[EJECT] of DISC on the EJECTfTILT screen again.
If the error indication still does not turn off after touching
[EJECT] of DISC on the EJECTfTILTscreen for a few times,
consult your Alpine dealer.
DISC ERROR
o
Scratched disc, contaminated disc/poor recording/disc
incompatible with this unit.
- Touch [EJECT] of DISC on the EJECTfTILT screen.
- Change the disc.
EJECT DISC BEFORE
USING DVD·SETUP
o
The DVD setup operation was attempted when a disc is inserted
in the unit.
- Eject the disc before the DVD setup operation.
I
UNSUPPORTED
I
(DivX· mode)
o
A sampling ratelbit rate not supported by the unit is used.
- Use a sampling ratelbit rate that is supported by the unit.
80-EN
Indication for CD changer
HI-TEMP
o
Protective circuit is activated due to high temperature.
- The indicator will disappear when the temperature returns to
within operation range.
ERROR01
o
Malfunction in the CD Changer.
- Consult your Alpine dealer. Press the magazine eject button
and pull out the magazine.
Check the indication. Insert the magazine again.
If the magazine cannot be pulled out, consult your Alpine
dealer.
o
Magazine ejection not possible.
- Press the magazine eject button. If the magazine does not eject,
consult your Alpine dealer.
ERROR02
o
A disc is left inside the CD Changer.
- Press the eject button to activate the eject function. When the
CD Changer finishes the eject function, insert an empty CD
magazine into the CD Changer to receive the disc left inside
the CD Changer.
INO MAGAZINEI
o
No magazine is loaded into the CD Changer.
- Insert a magazine.
NO DISC
o
No indicated disc.
- Choose another disc.