Table of Contents
Advertisement
<ZONE2/3/4/ REC SELECT>
SOURCE SELECT
<ZONE3 ON/OFF> <ZONE4 ON/OFF>
<ZONE2 ON/OFF>
[
AMP]
[Z2 ON]
[OFF]
VOLUME
[MUTE]
SOURCE
SELECT
(Main remote control unit)
Multi-zone
[ZONE SELECT]
indicator
[ON]
[OFF]
SOURCE SELECT
VOLUME
[MUTE]
[MENU]
(Sub remote control unit)
About the button names in these explanations
<
>
: Buttons on the main unit
[
]
: Buttons on the remote control unit
Button name only:
Buttons on the main unit and remote control unit
VOLUME
Multi-Zone Operations
Turning the Power On and Off
GOperation on the main unitH
<ZONE2 ON/OFF>
Press
the zone to be operated.
When the power turns on, the multi-zone indicator lights on the display.
GOperation on the remote control unitH
In the zone mode you want to operate, press
Selecting the Input Source
GOperation on the main unitH
<ZONE2/3/4 / REC SELECT>
q Press
<SOURCE SELECT>
w Turn
[ON]
GOperation on the remote control unitH
[OFF]
In the zone mode you want to operate, press
(ZONE3 or
ZONE4 mode)
Adjusting the Volume
[MENU]
GOperation on the main unitH
<ZONE2/3/4 / REC SELECT>
q Press
w Turn <VOLUME> to adjust.
GOperation on the remote control unitH
In the zone mode whose volume you want to adjust, press
[Variable range] – – – –70dB ~ –40dB ~ 18dB
• The volume can be adjusted when GUI menu "Manual Setup"
– "Zone Setup" – "(select the zone)" – "Volume Level" is set to
"Variable" . The volume can be increased up to the value set at
GUI menu "Manual Setup" – "Zone Setup" – "(select the zone)"
– "Volume Limit" (vpage 38).
• The volume for ZONE2 and ZONE3 can be adjusted with the remote
control unit.
<ZONE3 ON/OFF>
<ZONE4 ON/OFF>
,
or
for
[ON]
[OFF]
or
.
and select the zone to be adjusted.
.
[SOURCE SELECT]
.
and select the zone to be adjusted.
[VOLUME]
.
Turning off the Sound Temporarily
In the zone mode for which you want to mute the sound, press
[MUTE]
.
The sound is reduced to the level set at GUI menu "Manual Setup"
– "Zone Setup" – "(select the zone)" – "Mute Level" (vpage 38).
[MUTE]
To cancel, either adjust the volume or press
The setting is canceled when the zone's power is turned off.
• The source selected for ZONE3 is also output from the recording
output connectors.
[MENU]
• When the
is selected, it is possible to carryout "Zone Setup"
looking at the on-screen display in ZONE2. Also, when the "OSD" is
set as "ZONE2/ZONE3" , the on-screen display comes on the ZONE2
monitor when ZONE3 has been operated so it is possible to operate
it looking at this.
ZONE2 MENU
ZONE2 MENU
INPUT :DVD
SIGNAL:ANALOG
>Channel
VOL.
:-40dB
Vol.Lev.
Vol.Limit
>Bass
0dB
P.On Lev.
Treble
0dB
Mute Lev.
HPF
OFF
Lch Lev.
0dB
Rch Lev.
0dB
NOTE
• The digital signal from the digital input connectors (OPTICAL/
COAXIAL) are output to the analog audio connectors in ZONE2 and
ZONE3 in the case of PCM (2-channel) signals only.
• Digital audio signals input from the DENON LINK or HDMI connectors
cannot be played in multi-zone.
• The digital output (OPTICAL) from ZONE2 and ZONE4 cannot be
copyrighted network signals (internet radio, media server, and
USB).
• When certain digital signals are being input, noise may be output
from the ZONE2 and ZONE3 audio output connectors.
again.
STEREO
VAR
OFF
LAST
FULL
Advertisement
Table of Contents
