Table of Contents
Advertisement
Setting items
Surround Parameters
Subwoofer : Turn subwoofer output on and off.
•
ON : The subwoofer is used.
(Continued)
•
OFF : The subwoofer is not used.
Default : Restores all the surround parameter settings to their defaults.
•
No : Do not reset to the defaults.
•
Yes : Reset to the defaults.
If you select "Default" and press
Setting?" is displayed. Select "Yes" or "No", and then press
Tone
Tone Control : Sets the tone control function ON and OFF.
Adjust the tonal quality of
•
ON : Allow tone adjustment (treble, bass).
•
OFF : Playback without tone adjustment.
the sound.
•
This can be set when "Dynamic EQ" (vpage 69) is set to "OFF".
•
The tone cannot be adjusted in the direct mode.
Bass : Adjust low frequency range (bass).
•
–6dB ~ +6dB
This can be set when "Tone Control" (vpage 69) is set to "ON".
Treble : Adjust high frequency range (treble).
•
–6dB ~ +6dB
This can be set when "Tone Control" (vpage 69) is set to "ON".
Audyssey Settings
MultEQ : Corrects both time and frequency response problems in the
listening area.
Set MultEQ, Dynamic EQ
•
Audyssey : Optimize the frequency response of all speakers.
and Dynamic Volume.
•
Audyssey Byp.L/R : Optimize frequency response of speakers except
NOTE
front L and R speakers.
•
Audyssey Flat : Optimize frequency response of all speakers to flat
If you have not performed
Auto Setup, or if you change
response.
•
Manual : Apply frequency response set with "Manual EQ" (vpage
the speaker settings after
71).
performing Auto Setup, you
•
OFF : Turn "MultEQ" equalizer off.
may not be able to select
Dynamic
EQ/Dynamic
Volume, and "Run Audyssey"
•
"Audyssey", "Audyssey Byp. L/R" and "Audyssey Flat" can be
may be displayed.
selected after Audyssey Auto Setup has been performed. "Audyssey"
In this case, either perform
is automatically selected after performing Audyssey Auto Setup. "When
Audyssey Auto Setup over
"Audyssey", "Audyssey Byp. L/R" or "Audyssey Flat" is selected, "
again or perform "Restore"
lights.
(vpage 32) to return to the
•
After running Audyssey Auto Setup, if the Speaker Configuration,
settings after Audyssey Auto
Distance, Channel Level, and Crossover Frequency have changed without
Setup was run.
increasing the number of speakers measured, only "
•
If "Dynamic EQ" or "Dynamic Volume" is set to "ON" when "MultEQ"
is set to either "OFF" or "Manual", "MultEQ" is automatically set to
"Audyssey".
•
You can also press
Main remote control
operation buttons
Setting contents
ENTER
the message "Default
" lights.
MULTEQ
to set.
:Displaying the menu
:Moves the cursor
Cancel the menu
(Up/Down/Left/Right)
Setting items
Audyssey Settings
(Continued)
•
•
Dynamic EQ : Solves the problem of deteriorating sound quality as
volume is decreased by taking into account human perception and room
acoustics.
•
ENTER
.
•
•
•
•
•
•
•
"
:Confirm the setting
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
Setting contents
NOTE
"MultEQ" and "Manual EQ" cannot be selected when "EQ Customize"
is set to "Not Used" (vpage 37).
When using headphones, "MultEQ" is set to "OFF".
ON : Use the Dynamic EQ equalizer.
OFF : Do not use the Dynamic EQ equalizer.
After performing "Audyssey Auto Setup", the "Dynamic EQ" setting
automatically becomes "ON".
"
" is displayed when set to "ON".
When "MultEQ" is set to "OFF" or "Manual", "Dynamic EQ" is
automatically set to "OFF".
If "Dynamic Volume" is set to "ON", "Dynamic EQ" is automatically
set to "ON".
When you set "Dynamic EQ" to "ON", "Tone Control" is switched
"OFF".
[DYNAMIC EQ]
You can also press
to set.
Dynamic EQ / Volume : OFF
Dynamic EQ : ON/Volume : OFF
"Green"
"Red"
About Dynamic EQ
Audyssey Dynamic EQ solves the problem of deteriorating sound quality
as volume is decreased by taking into account human perception and
room acoustics. Audyssey Dynamic EQ works in tandem with Audyssey
MultEQ ® to provide well-balanced sound for every listener at any volume
level.
:Return to previous menu
ENGLISH
"OFF"
"Off"
See overleaf
Hide quick links:
Advertisement
Table of Contents
