Denon AVR-3310 Owner's Manual page 46

ENGLISH
Making Detailed Settings (Manual Setup)
Setting items
Trigger Out 1 When Setting for Zone (MAIN ZONE / ZONE2 / ZONE3)
n
Trigger out is activated through linkage to the power of the zone set to
Select the condition for
"ON".
activating Trigger Out 1 for
the input source, surround
n When Setting for Input Source
mode, etc.
Activate trigger out when the input source set to "ON" is selected.
See "TRIGGER OUT jacks"
Valid for the zone set to "ON" with "When Setting for Zone".
(vpage 21) for more
information on trigger out.
n When Setting for Surround Mode
Trigger Out 2
Activate trigger out when the surround mode set to "ON" is selected.
As with "Trigger Out 1",
Valid when the "MAIN ZONE" set to "ON" with "When Setting
select the condition for
for Zone" is selected, and when the input source set to "ON" with
activating Trigger Out 2.
"When Setting for Input Source" is selected.
• ON : Activate trigger on this mode.
• – – – : Do not activate trigger on this mode.
Remote ID 1 / 2 / 3 / 4
Set when you operate
When using the AVR-3310 with only the included main remote control
another DENON AV amplifier
unit (RC-1118), use Remote ID "1" (default).
with the remote control unit
When using the included sub remote control unit (RC-1121) and a
of the AVR-3310. Match the
separately sold remote control unit (RC-7000CI, etc.), this function
remote control unit you are
can be used. Match the ID setting of the remote control unit and the
using with the remote ID of
receiver.
the AVR-3310.
232C Port
Serial Control : Set when using an external controller.
2Way Remote : Set when using a 2-way remote control unit.
Set when using an external
controller or two-way remote
When using a DENON two-way remote control (RC-7000CI or RC-
control connected to the RS-
7001RCI, sold separately), set to "2Way Remote".
232C terminal.
NOTE
When setting to "2Way Remote", you can not use the RS-232C connector
as an external controller.
Dimmer Bright : Normal display brightness.
Dim : Reduced display brightness.
Adjust display brightness of
the receiver. Dark : Very low display brightness.
OFF : Turns the display off.

Main remote control
operation buttons
Setting contents
:Displaying the menu :Moves the cursor
Cancel the menu (Up/Down/Left/Right)
Setting items
Setup Lock OFF : Turn protection off.
ON : Turn protection on.
Protect settings from
inadvertent change.
• When "Setup Lock" is set to "ON", the settings listed below can no
longer be changed. Also, "SETUP LOCKED!" is displayed if you attempt
to operate related settings.
· GUI menu operations
· RESTORER
· Audio/Video Adjust
· MultEQ
· Dynamic EQ
• When canceling the setting, set "Setup Lock" to "OFF".
Maintenance Mode
NOTE
Used when receiving
Only use this function if so instructed by a DENON serviceperson or
maintenance from a DENON
installer.
service engineer or custom
installer.
Firmware Update Check for Update : You can check for firmware updates. You can also
check approximately how long it will take to complete an update.
Update the firmware of the
receiver.
Start : Execute the update process.
When updating starts, the power indicator becomes red and the GUI
screen is shut down. The amount of update time which has elapsed is
displayed.
When updating is complete the power indicator becomes green and
normal status is resumed.
If updating fails, the set automatically retries, but if updating is still not
b
possible, one of the messages shown below is displayed. If the display
reads as shown below, check the settings and network environment,
then update again.
Display
Updating failed
Login failed
Server is busy
Connection fail
Download fail
:Confirm the setting
Setting contents
· Dynamic Volume
· Channel Level
· Audio Delay
· Input Mode
Description
Updating failed.
Failure to log into server.
Server is busy. Wait a while then try again.
Failure connecting to server.
Downloading of the firmware has failed.
:Return to previous menu