Operations Common To Each Mode - Clarion CX400 Owner's Manual

Operations Common to Each Mode
or
Erasing the Personal Code
2-1. Select "CODE".
3-1. Press the
[~J~]
button.
The ERASE PERSONAL CODE screen
appears.
4-1. Enter the Personal Code currently.
5-1. Press and hold the
[~J~]
button for 2
seconds or longer.
Enter a Personal Code mode is cancelled.
For example:
Setting the anti-theft function (CATS)
"CATS" is the acronym of "Clarion Anti-Theft
System".
When you set a PIN code (called as "Personal
Code"), a theft is prevented by disabling the
operation of the unit at the theft.
Setting your Personal Code
2-1. Select "CODE".
3-1. Press the
[~J~]
button.
The set personal code screen appears.
4-1. Press the [DIRECT] buttons [1 ]-[6] to enter
your desired 4-digit Personal Code.
5-1. Press and hold the
[~NI~
]
button for 2
seconds or longer.
The entered Personal Code will be set, and
it will return to the previous screen.
Note:
• Write down your Personal Code in case you
forget it.
• Displaying the settings
The number of indicator of this unit decreases,
you can see the state of current settings at any
operation mode.
2-1. Select "SETTINGS".
3-1. Press the [.6.] or [T] button to display the
state of current settings.
* When the setting is selected, after 1 second
the current state will be displayed.
after 1 second,
1. Press and hold the [DISP] button for 1
second or longer to switch to the
adjustment selection display.
2. Press the
[~]
or
[~~]
button to select
the "item name".
"CLOCK"
+-+
"CONTRAST"
H
"SETTINGS"
H
"CODE"
< •
"XM SRC"
+-+
"SCRN SVR"
H
"MESSAGE INPUT"
H
"SCROLL"
<-.
"DIMMER"
+.
"BLINKLED"
H
"TEL-SP"
+-+
"TEL-SW"
H
"SYSTEM CHECK"
3. Press the [.6.] or [T] button to select the
"desired setting value".
*
In the case of display blinking "ENT", you
can press the
[~NI~
j button to adjust the
setting value.
*
After completing settings, press the [DISPj
button to return to the previous mode.
To
change adjustment setting
• Setting the clock
2-1. Select "CLOCK".
3-1. Press the
[~Jn
button.
3-2. Press the
[1<lIIII....]
or
[~~]
button to select the
hour or the minute.
3-3. Press the [.6.] or [T] button to set the
correct time.
*
The clock is displayed in 12-hour format.
3-4. Press the
[~J~]
button to store the time into
memory.
Note:
• You cannot set the clock when it is displayed
with only the ignition on. If you drain or remove
the car's battery or take out this unit, the clock is
reset. While setting the clock, if another button or
operation is selected, the clock set mode is
canceled.
• Setting the contrast
You can adjust the display contrast to match the
angle of installation of the unit.
*
The factory default setting is "10".
(Adjustment level: 1 to 16)
2-1. Select "CONTRAST".
3-1. Press the [.6.] or [T] button to adjust the
contrast.
CX400
23
Operations Common to Each Mode
or
Erasing the Personal Code
2-1. Select "CODE".
3-1. Press the
[~J~]
button.
The ERASE PERSONAL CODE screen
appears.
4-1. Enter the Personal Code currently.
5-1. Press and hold the
[~J~]
button for 2
seconds or longer.
Enter a Personal Code mode is cancelled.
For example:
Setting the anti-theft function (CATS)
"CATS" is the acronym of "Clarion Anti-Theft
System".
When you set a PIN code (called as "Personal
Code"), a theft is prevented by disabling the
operation of the unit at the theft.
Setting your Personal Code
2-1. Select "CODE".
3-1. Press the
[~J~]
button.
The set personal code screen appears.
4-1. Press the [DIRECT] buttons [1 ]-[6] to enter
your desired 4-digit Personal Code.
5-1. Press and hold the
[~NI~
]
button for 2
seconds or longer.
The entered Personal Code will be set, and
it will return to the previous screen.
Note:
• Write down your Personal Code in case you
forget it.
• Displaying the settings
The number of indicator of this unit decreases,
you can see the state of current settings at any
operation mode.
2-1. Select "SETTINGS".
3-1. Press the [.6.] or [T] button to display the
state of current settings.
* When the setting is selected, after 1 second
the current state will be displayed.
after 1 second,
1. Press and hold the [DISP] button for 1
second or longer to switch to the
adjustment selection display.
2. Press the
[~]
or
[~~]
button to select
the "item name".
"CLOCK"
+-+
"CONTRAST"
H
"SETTINGS"
H
"CODE"
< •
"XM SRC"
+-+
"SCRN SVR"
H
"MESSAGE INPUT"
H
"SCROLL"
<-.
"DIMMER"
+.
"BLINKLED"
H
"TEL-SP"
+-+
"TEL-SW"
H
"SYSTEM CHECK"
3. Press the [.6.] or [T] button to select the
"desired setting value".
*
In the case of display blinking "ENT", you
can press the
[~NI~
j button to adjust the
setting value.
*
After completing settings, press the [DISPj
button to return to the previous mode.
To
change adjustment setting
• Setting the clock
2-1. Select "CLOCK".
3-1. Press the
[~Jn
button.
3-2. Press the
[1<lIIII....]
or
[~~]
button to select the
hour or the minute.
3-3. Press the [.6.] or [T] button to set the
correct time.
*
The clock is displayed in 12-hour format.
3-4. Press the
[~J~]
button to store the time into
memory.
Note:
• You cannot set the clock when it is displayed
with only the ignition on. If you drain or remove
the car's battery or take out this unit, the clock is
reset. While setting the clock, if another button or
operation is selected, the clock set mode is
canceled.
• Setting the contrast
You can adjust the display contrast to match the
angle of installation of the unit.
*
The factory default setting is "10".
(Adjustment level: 1 to 16)
2-1. Select "CONTRAST".
3-1. Press the [.6.] or [T] button to adjust the
contrast.
CX400
23